Input Shaft Oil Seal
Components
COMPONENTS
ILLUSTRATION
*1 |
INPUT SHAFT TYPE T OIL SEAL |
*2 |
HYBRID VEHICLE TRANSAXLE ASSEMBLY |
● |
Non-reusable part |
![]() |
MP grease |
Replacement
REPLACEMENT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during input shaft type T oil seal removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here *1: The vehicle height changes because of suspension or tire replacement |
|||
Auxiliary battery terminal is disconnected/reconnected |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
Pre-collision system |
|||
Intelligent clearance sonar system* |
|||
Lighting system (w/ AFS)(EXT) |
|||
Memorize steering angle neutral point |
Parking assist monitor system |
||
Panoramic view monitor system |
|||
Replacement of ECM |
Perform Vehicle Identification Number (VIN) registration |
MIL illuminates |
|
|
Inspection After Repair |
|
|
Replacement of inverter with converter assembly |
Resolver learning |
|
|
Front wheel alignment adjustment |
|
|
|
|
|
|
|
Suspension, tires, etc.*1 |
Rear television camera assembly optical axis (Back camera position setting) |
Parking assist monitor system |
|
Replacement of front bumper assembly |
Front television camera view adjustment |
Panoramic view monitor system |
|
Suspension, tires, etc.*1 |
|
||
|
|
Lighting system (w/ AFS)(EXT) |
|
Suspension, tires, etc.*1 |
Perform headlight ECU sub-assembly LH initialization |
||
CAUTION:
- Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
Click here

- To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

- To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

- To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

- The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
*a
An Object Exceeding Weight Limit of Engine Lifter
- The hybrid vehicle transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.
*a
Object Exceeding Weight Limit of Transmission Jack
NOTICE:
- After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here

- If the ECM has been struck or dropped, replace it.
- Perform Vehicle Identification Number (VIN) registration when replacing the ECM.
Click here

PROCEDURE
1. REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY
Click here ![]()
2. REMOVE INPUT SHAFT TYPE T OIL SEAL
(a) Using a screwdriver with its tip wrapped with protective tape, remove the input shaft type T oil seal from the hybrid vehicle transaxle assembly. NOTICE: Be careful not to damage the input shaft assembly or hybrid vehicle transaxle assembly. |
|
3. INSTALL INPUT SHAFT TYPE T OIL SEAL
(a) Coat the lip of a new input shaft type T oil seal with a small amount of MP grease.
(b) Using SST and a hammer, install the input shaft type T oil seal to the hybrid vehicle transaxle assembly. SST: 09608-04031 Standard Depth: 1.9 to 2.7 mm (0.0748 to 0.106 in.) NOTICE:
|
|
4. INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY
Click here ![]()


