Transmission Wire
Components
COMPONENTS
ILLUSTRATION
*A |
Type A |
*B |
Type B |
*1 |
FRONT FENDER APRON SEAL LH |
*2 |
FRONT WHEEL OPENING EXTENSION PAD LH |
*3 |
FRONT WHEEL OPENING EXTENSION PAD RH |
*4 |
NO. 1 ENGINE UNDER COVER |
*5 |
REAR ENGINE UNDER COVER LH |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*1 |
REFILL PLUG |
*2 |
NO. 1 TRANSMISSION OIL FILLER TUBE |
*3 |
OVERFLOW PLUG |
*4 |
GASKET |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● |
Non-reusable part |
![]() |
Toyota Genuine ATF WS |
- |
- |
ILLUSTRATION
*1 |
FRONT SUSPENSION MEMBER DYNAMIC DAMPER |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*A |
for TMC Made |
*B |
for TMMWV Made |
*1 |
TRANSMISSION CASE SIDE COVER |
- |
- |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● |
Non-reusable part |
![]() |
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent |
★ |
Precoated part |
ILLUSTRATION
*1 |
OIL COOLER UNION SUB-ASSEMBLY |
*2 |
OIL COOLER UNION BOLT |
*3 |
TRANSMISSION WIRE |
*4 |
TEMPERATURE SENSOR CLAMP |
*5 |
GASKET |
- |
- |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● |
Non-reusable part |
![]() |
Toyota Genuine ATF WS |
- |
- |
Installation
INSTALLATION
PROCEDURE
1. INSTALL TRANSMISSION WIRE
(a) Coat the O-ring of the transmission wire with Toyota Genuine ATF WS. |
![]() |
(b) Install the transmission wire to the automatic transaxle case sub-assembly with the bolt.
Torque:
5,4 N·m {55 kgf·cm, 48 in·lbf}
(c) Connect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector.
(d) Install the temperature sensor to the transmission valve body assembly with the bolt and temperature sensor clamp.
Torque:
10,8 N·m {110 kgf·cm, 8 ft·lbf}
NOTICE:
To prevent it from being pinched between the transmission valve body assembly and the transmission case side cover, pass the transmission revolution sensor (NC) wire under the transmission wire (temperature sensor wire) as shown in the illustration.
*a |
Transmission Wire (Temperature Sensor Wire) |
*b |
Transmission Revolution Sensor (NC) Wire |
(e) Connect the 9 solenoid valve connectors.
![]() |
Do not let transmission wire protrude into this area. |
- To prevent it from being pinched between the transmission valve body assembly and the transmission case side cover, do not let the transmission wire ride up over the area shown in the illustration.
- To prevent it from being pinched between the transmission case side cover and the automatic transaxle case sub-assembly, do not let the transmission wire protrude toward the transmission case side cover installation surface.
(f) Engage the clamp to connect the transmission wire to the solenoid lock plate. |
![]() |
(g) Connect the transmission wire connector, rotate the lever and engage the claw. HINT: Rotate the lever until the claw of the transmission wire connector makes a click sound. |
![]() |
2. INSTALL TRANSMISSION CASE SIDE COVER (for TMC Made)
HINT:
TMC Made and TMMWV Made components can be identified by the location where the serial number is stamped.
*a |
TMC Made |
*b |
TMMWV Made |
(a) Clean the transmission case side cover installation surface of the automatic transaxle case sub-assembly.
![]() |
Area to be Cleaned |
NOTICE:
Completely remove any oil or grease from the contact surfaces of the automatic transaxle case sub-assembly.
(b) Temporarily install a new transmission case side cover to the automatic transaxle case sub-assembly with the 2 bolts (A and B). NOTICE: To avoid damaging the gasket, prevent it from contacting the surrounding area during installation procedures. |
![]() |
(c) Temporarily install the 8 bolts (C).
(d) Fully tighten the 10 bolts in the order shown in the illustration. Torque: 7 N·m {71 kgf·cm, 62 in·lbf} |
![]() |
3. INSTALL TRANSMISSION CASE SIDE COVER (for TMMWV Made)
HINT:
TMC Made and TMMWV Made components can be identified by the location where the serial number is stamped.
*a |
TMC Made |
*b |
TMMWV Made |
(a) Clean the transmission case side cover installation surface of the automatic transaxle case sub-assembly.
![]() |
Area to be Cleaned |
NOTICE:
Completely remove any oil or grease from the contact surfaces of the automatic transaxle case sub-assembly.
(b) Clean the 3 bolt holes shown in the illustration. |
![]() |
(c) Apply adhesive to 2 or 3 threads on the end of the bolt (A) and 2 bolts (D). Adhesive: Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent NOTICE: Make sure to install the bolts immediately after applying adhesive to prevent foreign matter from attaching to them. HINT: The bolt (A) and 2 bolts (D) are in the locations shown in the following step. |
|
(d) Temporarily install a new transmission case side cover to the automatic transaxle case sub-assembly with the 2 bolts ((A) and (B)). NOTICE:
|
![]() |
(e) Temporarily install the 6 bolts (C) and 2 bolts (D).
NOTICE:
Bolt (D) is an adhesive-coated bolt.
(f) Fully tighten the 10 bolts in the order shown in the illustration. Torque: Bolt (A) and Bolt (D) : 6,5 N·m {66 kgf·cm, 58 in·lbf} Bolt (B) and Bolt (C) : 7 N·m {71 kgf·cm, 62 in·lbf} |
![]() |
4. INSTALL OIL COOLER UNION SUB-ASSEMBLY
(a) Pass the oil cooler union sub-assembly through 2 new gaskets and temporarily install it to the automatic transaxle case sub-assembly with the oil cooler union bolt. |
|
(b) Temporarily install the oil cooler union sub-assembly bracket portion to the automatic transaxle case sub-assembly with the bolt.
(c) Fully tighten the oil cooler union bolt.
Torque:
23 N·m {230 kgf·cm, 17 ft·lbf}
(d) Fully tighten the bolt.
Torque:
12 N·m {122 kgf·cm, 9 ft·lbf}
5. INSTALL FRONT SUSPENSION MEMBER DYNAMIC DAMPER
Click here ![]()
6. INSTALL FRONT ENGINE MOUNTING INSULATOR
Click here ![]()
7. ADJUST AUTOMATIC TRANSAXLE FLUID
Click here ![]()
8. INSTALL FRONT FENDER APRON SEAL LH
Click here ![]()
9. INSTALL REAR ENGINE UNDER COVER LH
Click here ![]()
10. INSTALL NO. 1 ENGINE UNDER COVER
Click here ![]()
11. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH
Click here ![]()
12. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH
Click here ![]()
13. INSTALL FRONT WHEEL LH
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission wire removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
Replacement of automatic transaxle fluid |
ATF thermal degradation estimate reset |
The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly |
PROCEDURE
1. REMOVE FRONT WHEEL LH
Click here ![]()
2. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH
Click here ![]()
3. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH
Click here ![]()
4. REMOVE NO. 1 ENGINE UNDER COVER
Click here ![]()
5. REMOVE REAR ENGINE UNDER COVER LH
Click here ![]()
6. REMOVE FRONT FENDER APRON SEAL LH
Click here ![]()
7. DRAIN AUTOMATIC TRANSAXLE FLUID
(a) Remove the refill plug and gasket from the automatic transaxle case sub-assembly. |
![]() |
(b) Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle housing. |
![]() |
(c) Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle housing and drain the automatic transaxle fluid. |
|
(d) Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle housing.
Torque:
1,7 N·m {17 kgf·cm, 15 in·lbf}
(e) Using a 10 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the transaxle housing.
HINT:
Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.
(f) Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage.
HINT:
Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.
8. REMOVE FRONT ENGINE MOUNTING INSULATOR
Click here ![]()
9. REMOVE FRONT SUSPENSION MEMBER DYNAMIC DAMPER
Click here ![]()
10. SEPARATE OIL COOLER UNION SUB-ASSEMBLY
(a) Remove the bolt to separate the oil cooler union sub-assembly bracket portion from the automatic transaxle case sub-assembly. |
|
(b) Remove the oil cooler union bolt and 2 gaskets to separate the oil cooler union sub-assembly from the automatic transaxle case sub-assembly.
11. REMOVE TRANSMISSION CASE SIDE COVER
(a) Remove the 10 bolts and transmission case side cover from the automatic transaxle case sub-assembly. |
|
12. REMOVE TRANSMISSION WIRE
(a) Disengage the claw, rotate the lever and disconnect the transmission wire connector. |
![]() |
(b) Disengage the clamp to disconnect the transmission wire from the solenoid lock plate. |
|
(c) Disconnect the 9 solenoid valve connectors.
HINT:
- Using a screwdriver, disconnect the solenoid valve connector (A) using the procedure shown in the illustration.
- Using a screwdriver, disconnect the solenoid valve connector (B) using the procedure shown in the illustration.
(d) Remove the bolt and temperature sensor clamp and disconnect the temperature sensor from the transmission valve body assembly. |
![]() |
(e) Disconnect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector. |
![]() |
(f) Remove the bolt and transmission wire from the automatic transaxle case sub-assembly. |
![]() |
























