Pressure Control Solenoid "D" Circuit Short to Ground or Open (P271314). Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Battery (P275612). Torque Converter Clutch Pressure
Pressure Control Solenoid "D" Circuit Short to Ground or Open (P271314)
DESCRIPTION
Refer to DTC P27137F.
Click here ![]()
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
P271314 |
Pressure Control Solenoid "D" Circuit Short to Ground or Open |
While the engine is running, a short to ground or open is detected in the solenoid (SLT) valve circuit for 1 second (1-trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P2720 |
MONITOR DESCRIPTION
When an open or short to ground in the solenoid (SLT) valve circuit is detected, the ECM will determine that there is a malfunction, illuminate the MIL and store this DTC.
MONITOR STRATEGY
Related DTC |
P2720: Solenoid (SLT) valve/Range check (Low current) |
Required sensors/components |
Solenoid (SLT) valve |
Frequency of operation |
Continuous |
Duration |
Condition (a): 1 sec. Condition (b): 1.1 sec. |
MIL operation |
Immediate |
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
The monitor will run whenever the following DTCs are not stored |
None |
Solenoid current cut status |
Not cut |
Engine switch |
On (IG) |
Starter |
OFF |
Battery voltage |
10.5 V or more |
Target current (0.1 sec. or more) |
0.2 A or more |
TYPICAL MALFUNCTION THRESHOLDS
Any of the following conditions are met |
(a) or (b) |
(a) Solenoid current |
Less than 0.075 A |
(b) Solenoid high current cutout by solenoid driver IC |
ON |
COMPONENT OPERATING RANGE
Solenoid current |
0.075 A or more |
Solenoid high current cutout by solenoid driver IC |
OFF |
CONFIRMATION DRIVING PATTERN
HINT:
- After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
- When clearing the permanent DTCs, refer to the Clear Permanent DTC procedure.
Click here

- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the engine switch off and wait for 2 minutes or more.
- Turn the engine switch on (IG) and turn the Techstream on.
- Start the engine.
- Wait for 2 seconds or more with the engine running. [*1]
HINT:
[*1] : Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
- Input the DTC: P271314.
- Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
N/A
- Unable to perform DTC judgment
- Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
WIRING DIAGRAM
Refer to DTC P271312.
Click here ![]()
NOTICE:
- Perform the universal trip to clear permanent DTCs.
Click here

- Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click here

PROCEDURE
CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SOLENOID (SLT) VALVE) - ECM)
(a) Disconnect the C56 ECM connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
C56-67 (SLT+) - C56-37 (SLT-) |
20 °C |
5.0 to 5.6 Ω |
C56-67 (SLT+) or C56-37 (SLT-) - Body ground and other terminals |
Always |
10 kΩ or higher |
| NG | GO TO STEP 3 |
|
REPLACE ECM
(a) Replace the ECM.
Click here ![]()
| NEXT | PERFORM REGISTRATION |
CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
(a) Disconnect the C52 transmission wire connector.
(b) Disconnect the C56 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
C52-24 (SLT+) - C56-67 (SLT+) |
Always |
Below 1 Ω |
C52-23 (SLT-) - C56-37 (SLT-) |
Always |
Below 1 Ω |
C52-24 (SLT+) or C56-67 (SLT+) - Body ground and other terminals |
Always |
10 kΩ or higher |
C52-23 (SLT-) or C56-37 (SLT-) - Body ground and other terminals |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM) |
|
INSPECT SOLENOID (SLT) VALVE
(a) Remove the solenoid (SLT) valve. Click here |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
Solenoid (SLT) valve connector terminal 1 - terminal 2 |
20 °C |
5.0 to 5.6 Ω |
(c) Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.
OK:
Valve moves and makes an operating sound.
| OK | REPAIR OR REPLACE TRANSMISSION WIRE |
| NG | REPLACE SOLENOID (SLT) VALVE |
Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Battery (P275612)
DESCRIPTION
The ECM controls the solenoid (SLU) valve using a predetermined current, and performs lock-up and flex lock-up control.
*1 |
Spool Valve |
*2 |
Sleeve |
*3 |
Solenoid Coil |
- |
- |
*a |
Current |
*b |
Hydraulic Pressure |
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
P275612 |
Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Battery |
While the vehicle is being driven, a short to +B is detected in the solenoid (SLU) valve circuit for 1 second (1-trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P2763 |
MONITOR DESCRIPTION
When a short to +B in the solenoid (SLU) valve circuit is detected, the ECM will determine that there is a malfunction, illuminate the MIL and store this DTC.
MONITOR STRATEGY
Related DTCs |
P2763: Solenoid (SLU) valve/Range check (High current) |
Required sensors/components |
Solenoid (SLU) valve |
Frequency of operation |
Continuous |
Duration |
1 sec. |
MIL operation |
Immediate |
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
AllThe monitor will run whenever the following DTCs are not stored |
None |
Solenoid current cut status |
Not cut |
Engine switch |
On (IG) |
Starter |
OFF |
Battery voltage |
10.5 V or more |
Battery voltage |
8 V or more and less than 12.499 V |
Target current (0.1 sec. or more) |
0.8 A or less |
Battery voltage |
12.5 V or more and less than 16 V |
Target current (0 sec. or more) |
1 A or less |
TYPICAL MALFUNCTION THRESHOLDS
Any of the following conditions are met: Condition (A) or (B)
Condition (A)Battery voltage |
8 V or more and less than 12.499 V |
Solenoid current |
More than 0.92 A |
Battery voltage |
12.5 V or more and less than 16 V |
Solenoid current |
More than 1.1 A |
COMPONENT OPERATING RANGE
Both of the following conditions are met: Condition (A) and (B)
Condition (A)Battery voltage |
8 V or more and less than 12.499 V |
Solenoid current |
0.92 A or less |
Battery voltage |
12.5 V or more and less than 16 V |
Solenoid current |
1.1 A or less |
CONFIRMATION DRIVING PATTERN
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
- After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
- When clearing the permanent DTCs, refer to the Clear Permanent DTC procedure.
Click here

- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the engine switch off and wait for 2 minutes or more.
- Turn the engine switch on (IG) and turn the Techstream on.
- Start the engine.
- Perform the Lock-up Function inspection in Road Test. [*1]
Click here

HINT:
[*1] : Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Stop the vehicle.
- Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
- Input the DTC: P275612.
- Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
N/A
- Unable to perform DTC judgment
- Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
WIRING DIAGRAM
NOTICE:
- Perform the universal trip to clear permanent DTCs.
Click here

- Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click here

PROCEDURE
CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SOLENOID (SLU) VALVE) - ECM)
(a) Disconnect the C56 ECM connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
C56-76 (SLU+) or C56-61 (SLU-) - Other terminals |
Always |
10 kΩ or higher |
| NG | GO TO STEP 3 |
|
REPLACE ECM
(a) Replace the ECM.
Click here ![]()
| NEXT | PERFORM REGISTRATION |
CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
(a) Disconnect the C52 transmission wire connector.
(b) Disconnect the C56 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
C52-5 (SLU+) or C56-76 (SLU+) - Other terminals |
Always |
10 kΩ or higher |
C52-4 (SLU-) or C56-61 (SLU-) - Other terminals |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM) |
|
INSPECT SOLENOID (SLU) VALVE
(a) Remove the solenoid (SLU) valve. Click here |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
Solenoid (SLU) valve connector terminal 1 - terminal 2 |
20 °C |
5.0 to 5.6 Ω |
(c) Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.
OK:
Valve moves and makes operating sound.
| OK | REPAIR OR REPLACE TRANSMISSION WIRE |
| NG | REPLACE SOLENOID (SLU) VALVE |
Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Ground or Open (P275614)
DESCRIPTION
Refer to DTC P275612.
Click here
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
P275614 |
Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Ground or Open |
While the vehicle is being driven, a short to ground or open is detected in the solenoid (SLU) valve circuit for 1 second (1-trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P2764 |
MONITOR DESCRIPTION
When an open or short to ground in the solenoid (SLU) valve circuit is detected, the ECM will determine that there is a malfunction, illuminate the MIL and store this DTC.
MONITOR STRATEGY
Related DTCs |
P2764: Solenoid (SLU) valve/Range check (Low current) |
Required sensors/components |
Solenoid (SLU) valve |
Frequency of operation |
Continuous |
Duration |
1 sec. |
MIL operation |
Immediate |
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
The monitor will run whenever the following DTCs are not stored |
None |
Solenoid current cut status |
Not cut |
Engine switch |
On (IG) |
Starter |
OFF |
Battery voltage |
10.5 V or more |
Target current (0.1 sec. or more) |
0.2 A or more |
TYPICAL MALFUNCTION THRESHOLDS
Solenoid current |
Less than 0.075 A |
COMPONENT OPERATING RANGE
Solenoid current |
0.075 A or more |
CONFIRMATION DRIVING PATTERN
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
- After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
- When clearing the permanent DTCs, refer to the Clear Permanent DTC procedure.
Click here
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the engine switch off and wait for 2 minutes or more.
- Turn the engine switch on (IG) and turn the Techstream on.
- Start the engine.
- Perform the Lock-up Function inspection in Road Test. [*1]
Click here
HINT:
[*1] : Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Stop the vehicle.
- Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
- Input the DTC: P275614.
- Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
N/A
- Unable to perform DTC judgment
- Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
WIRING DIAGRAM
Refer to DTC P275612.
Click here
NOTICE:
- Perform the universal trip to clear permanent DTCs.
Click here
- Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click here
PROCEDURE
CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SOLENOID (SLU) VALVE) - ECM)
(a) Disconnect the C56 ECM connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
C56-76 (SLU+) - C56-61 (SLU-) |
20 °C |
5.0 to 5.6 Ω |
C56-76 (SLU+) or C56-61 (SLU-) - Body ground and other terminals |
Always |
10 kΩ or higher |
| NG | GO TO STEP 3 |
|
REPLACE ECM
(a) Replace the ECM.
Click here
| NEXT | PERFORM REGISTRATION |
CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
(a) Disconnect the C52 transmission wire connector.
(b) Disconnect the C56 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
C52-5 (SLU+) - C56-76 (SLU+) |
Always |
Below 1 Ω |
C52-4 (SLU-) - C56-61 (SLU-) |
Always |
Below 1 Ω |
C52-5 (SLU+) or C56-76 (SLU+) - Body ground and other terminals |
Always |
10 kΩ or higher |
C52-4 (SLU-) or C56-61 (SLU-) - Body ground and other terminals |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM) |
|
INSPECT SOLENOID (SLU) VALVE
(a) Remove the solenoid (SLU) valve. Click here |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
Solenoid (SLU) valve connector terminal 1 - terminal 2 |
20 °C |
5.0 to 5.6 Ω |
(c) Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.
OK:
Valve moves and makes operating sound.
| OK | REPAIR OR REPLACE TRANSMISSION WIRE |
| NG | REPLACE SOLENOID (SLU) VALVE |

