ECU Terminals
ECU TERMINALS
INSPECT FRONT WIPER RELAY ASSEMBLY (with rain sensor)
(a) Disconnect connector F56 from the front wiper relay assembly.
(1) Measure the voltage and resistance at the connector on the wire harness side according to the value(s) in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F56-2 (IG) - Body ground |
B - Body ground |
Ignition switch ON signal (power supply circuit) |
Ignition Switch in ON position |
11 à 14 V |
Ignition Switch in OFF position |
Below 1 V |
|||
F56-25 (W) - Body ground |
B - Body ground |
Front washer switch signal |
Front washer switch in ON position |
Below 1 Ω |
Front washer switch in OFF position |
10 kΩ minimum |
|||
F56-8 (VR2) - F56-21 (VR1) |
W - G |
Volume adjustment signal |
Sensitivity control switch* changed |
0 à 231 Ω |
F56-12 (E) - Body ground |
W-B - Body ground |
Body ground |
Always |
Below 1 Ω |
F56-16 (WIG) - Body ground |
B - Body ground |
Power source signal |
Ignition Switch in ON position |
11 à 14 V |
Ignition Switch in OFF position |
Below 1 V |
HINT:
*: Rain sensor sensitivity can be adjusted using the sensitivity control switch.
If the result is not as specified, there may be a malfunction in the wire harness.
(b) Reconnect connector F56 to the front wiper relay assembly.
(1) Measure the resistance according to the value(s) shown in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F56-10 (+1) - Body ground |
G - Body ground |
Front wiper motor low speed signal |
Front wiper motor in OFF position |
Below 1 Ω |
HINT:
If the result is not as specified, the front wiper relay assembly may be faulty.
(2) Measure the voltage and check the pulses according to the value(s) in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F56-1 (+SM) - Body ground |
G - Body ground |
Front wiper motor position detection signal |
Front wiper motor operating at high or low speed |
Below 1 V ←→ 11 to 14 V |
Front wiper motor in OFF position |
Below 1 V |
|||
F56-3 (C1) - F56-5 (CO) |
V - Y |
Front wiper switch AUTO signal |
Ignition switch ON, front wiper switch in AUTO position |
Below 1 V |
Ignition switch ON, front wiper switch in OFF position |
11 à 14 V |
|||
F56-25 (W) - Body ground |
B - Body ground |
Front washer switch signal |
Ignition switch ON, headlight washer switch in ON position |
Below 1 V |
Ignition switch ON, front washer switch in OFF position |
11 à 14 V |
|||
F56-10 (+1) - Body ground |
G - Body ground |
Front wiper motor low speed signal |
Front wiper motor operating in LOW position |
11 à 14 V |
F56-11 (+2) - Body ground |
W - Body Ground |
Front wiper motor high speed signal |
Front wiper motor operating in HIGH position |
11 à 14 V |
Front wiper motor in OFF position |
Below 1 V |
|||
F56-14 (MPX1) - Body ground |
V - Body ground |
Rain sensor signal |
Ignition Switch in ON position |
Pulse generation |
F56-24 (SPD) - Body ground |
V - Body ground |
Vehicle speed signal |
Vehicle driven at approximately 20 km/h |
Pulse generation (see waveform 1) |
HINT:
If the result is not as specified, the front wiper relay assembly may be faulty.
(3) Waveform 1 (reference):
Item | Condition |
|---|---|
Tester Connection |
F56-24 (SPD) - Body ground |
Oscilloscope Setting |
5 V/DIV., 20 ms/DIV. |
Vehicle Operating Conditions |
Vehicle driven at approximately 20 km/h |
HINT:
When the system operates normally, one wheel revolution generates 4 pulses. As vehicle speed increases, the width indicated by A in the illustration decreases.
CHECK COMBINATION METER ASSEMBLY
(a) Measure the voltage according to the value(s) shown in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F4-17 (WLVL) - Body ground*1 |
LG - Body ground |
Washer fluid level signal |
Ignition switch ON, washer fluid level not low |
11 à 14 V |
Ignition switch ON, washer fluid level low |
Below 1 V |
- *1: for vehicles for cold regions
(b) Measure the waveform according to the value(s) in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F4-6 (+S) - Body ground |
V - Body ground |
Speed signal from other system (output) |
Vehicle driven at approximately 20 km/h |
Pulse generation (see waveform 1) |
(1) Waveform 1 (reference):
Item | Condition |
|---|---|
Tester Connection |
F4-6 (+S) - Body ground |
Oscilloscope Setting |
5 V/DIV., 20 ms/DIV. |
Vehicle Operating Conditions |
Vehicle driven at approximately 20 km/h |
HINT:
When the system operates normally, one wheel revolution generates 4 pulses. As vehicle speed increases, the width indicated by A in the illustration decreases.