Supplemental Restraint Systems

Passenger buckle switch circuit malfunction (B1771)

~9min read

DESCRIPTION

The passenger buckle switch circuit consists of the occupant detection ECU and the passenger buckle switch (front passenger seat inner belt assembly).

DTC B1771 is stored when a malfunction is detected in the passenger buckle switch circuit.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

B1771

Front Passenger Seat Belt Buckle Switch Circuit Malfunction

One of the following conditions is met

  • The occupant detection ECU detects a short circuit in the passenger buckle switch circuit.
  • The occupant detection ECU detects a short to ground in the passenger buckle switch circuit.
  • The occupant detection ECU detects a short to B+ in the passenger buckle switch circuit.
  • The occupant detection ECU detects an open in the passenger buckle switch circuit.
  • Passenger buckle switch malfunction
  • Occupant Detection ECU Malfunction
  • Front Seat RH Wire
  • Passenger buckle switch (front passenger seat inner belt assembly)
  • Occupant Detection ECU
DTC Detection Conditions

Vehicle Operating Conditions

Sequence 1

Sequence 2

Sequence 3

Sequence 4

Sequence 5

Sequence 6

Diagnostic Condition

Ignition Switch in ON position

○

○

○

○

○

○

Malfunction Status

The occupant detection ECU detects a short circuit in the passenger buckle switch circuit.

○

-

-

-

-

-

The occupant detection ECU detects a short to ground in the passenger buckle switch circuit.

-

○

-

-

-

-

The occupant detection ECU detects a short to B+ in the passenger buckle switch circuit.

-

-

○

-

-

-

The occupant detection ECU detects an open in the passenger buckle switch circuit.

-

-

-

○

-

-

Passenger buckle switch malfunction

-

-

-

-

○

-

Occupant Detection ECU Malfunction

-

-

-

-

-

○

Detection Duration

-

-

-

-

-

-

Number of Trips

1 trip(s)

1 trip(s)

1 trip(s)

1 trip(s)

1 trip(s)

1 trip(s)

HINT:

The DTC is output when the conditions for any one of the sequences in the table above are met.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.

Click here

HINT:

  • If DTC B1650/32 is stored as a result of the airbag system troubleshooting, check the DTCs stored in the occupant detection ECU. If DTC B1771 is output, troubleshoot this DTC first.
  • If troubleshooting is difficult (wire harness check), remove the front passenger seat mounting bolts to see underneath the seat cushion.
  • In the case mentioned above, lift and hold the seat so that it does not fall. Only hold the seat if necessary, as holding the seat for a long period may deform the seat rail.

PROCEDURE

  1. CHECK CONNECTORS

(a) Turn the ignition switch OFF.

(b) Disconnect the cable from the negative (-) battery terminal.

(c) Check that the connectors are properly connected to the occupant detection ECU and the front passenger seat inner belt assembly.

OK:

The connectors are properly connected.

HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next check.

(d) Disconnect the connectors from the occupant detection ECU and the front passenger seat inner belt assembly.

(e) Check that the connector terminals are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

NG

REPLACE FRONT RH SEAT WIRE HARNESS

OK
  1. CHECK FRONT RH SEAT WIRE HARNESS (SHORT TO B+)

(a) Connect the cable to the negative (-) battery terminal.

*1

Front RH Seat Belt Inner Belt Assembly

*2

Occupant Detection ECU

*3

Front Seat RH Wire

*a

Front view of wire harness side connector

(to occupant detection ECU)

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

Y6-7 (BSW) - Body ground

Ignition Switch in ON position

Below 1 V

Y6-9 (BGND) - Body ground

Ignition Switch in ON position

Below 1 V

(d) Turn the ignition switch to OFF.

(e) Disconnect the cable from the negative (-) battery terminal.

NG

REPLACE FRONT RH SEAT WIRE HARNESS

OK
  1. CHECK FRONT RH SEAT WIRE HARNESS (OPEN)

(a) Using a diagnostic cable, connect terminals 1 (+) and 2 (-) of connector B.

NOTICE:

Do not force the diagnosis cable into the connector terminals when connecting the cable.

*1

Front RH Seat Belt Inner Belt Assembly

*2

Occupant Detection ECU

*3

Front Seat RH Wire

*4

Diagnosis cable

*a

Front view of wire harness side connector

(to occupant detection ECU)

*b

Front view of wire harness side connector

(to front passenger seat inner belt assembly)

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

Y6-7 (BSW) - Y6-9 (BGND)

Always

Below 1 Ω

(c) Disconnect the diagnostic cable from connector C.

NG

REPLACE FRONT RH SEAT WIRE HARNESS

OK
  1. CHECK FRONT RH SEAT WIRE HARNESS (SHORT CIRCUIT)

(a) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

Y6-7 (BSW) - Y6-9 (BGND)

Always

1 MΩ or higher

*1

Front RH Seat Belt Inner Belt Assembly

*2

Occupant Detection ECU

*3

Front Seat RH Wire

*a

Front view of wire harness side connector

(to occupant detection ECU)

NG

REPLACE FRONT RH SEAT WIRE HARNESS

OK
  1. CHECK FRONT RH SEAT WIRE HARNESS (SHORT TO GROUND)

(a) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

Y6-7 (BSW) - Body ground

Always

1 MΩ or higher

Y6-9 (BGND) - Body ground

Always

1 MΩ or higher

*1

Front RH Seat Belt Inner Belt Assembly

*2

Occupant Detection ECU

*3

Front Seat RH Wire

*a

Front view of wire harness side connector

(to occupant detection ECU)

NG

REPLACE FRONT RH SEAT WIRE HARNESS

OK
  1. CHECK DTCs

(a) Connect the connectors to the occupant detection ECU and the front passenger seat inner belt assembly.

(b) Connect the cable to the negative (-) battery terminal.

(c) Clear the DTCs stored in the occupant detection ECU.

Click here

Body Electrical > Occupant Detection > Clear DTCs

(d) Clear the DTCs stored in the airbag sensor assembly.

Click here

Body Electrical > SRS Airbag > Clear DTCs

(e) Turn the ignition switch to OFF.

(f) Turn the ignition switch to ON and wait for at least 10 seconds.

(g) Check the DTCs.

Click here

Body Electrical > Occupant Detection > Trouble Codes

OK:

DTC B1771 is not output.

HINT:

Other codes may be output at this point, but they are not related to this check.

(h) Turn the ignition switch OFF.

OK

USE SIMULATION METHOD TO CHECK

NG
  1. CHECK FRONT PASSENGER SEAT INNER BELT ASSEMBLY

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Replace the front passenger seat inner belt assembly with a normal one.

Click here

HINT:

Perform the following check using a known good part, if possible, taken from another vehicle.

(c) Connect the cable to the negative (-) battery terminal.

(d) Clear the DTCs stored in the occupant detection ECU.

Click here

Body Electrical > Occupant Detection > Clear DTCs

(e) Clear the DTCs stored in the airbag sensor assembly.

Click here

Body Electrical > SRS Airbag > Clear DTCs

(f) Turn the ignition switch to the OFF position.

(g) Turn the ignition switch to ON and wait for at least 10 seconds.

(h) Check the DTCs.

Click here

Body Electrical > Occupant Detection > Trouble Codes

OK:

DTC B1771 is not output.

HINT:

Other codes may be output at this point, but they are not related to this check.

(i) Turn the ignition switch to OFF.

(j) Disconnect the cable from the negative (-) battery terminal.

(k) Reinstall the front passenger seat inner belt assembly in its original location (it was temporarily moved for testing).

Click here

OK

REPLACE FRONT RH SEAT BELT INNER BELT ASSEMBLY

NG
  1. REPLACE OCCUPANT DETECTION ECU

(a) Turn the ignition switch OFF.

(b) Disconnect the cable from the negative (-) battery terminal.

(c) Replace the occupant detection ECU with a new one.

Click here

(d) Connect the cable to the negative (-) battery terminal.

NEXT
  1. PERFORM ZERO POINT CALIBRATION

(a) Using the Techstream, perform zero point calibration.

Click here

Body Electrical > Occupant Detection > Utility

Zero Point Calibration

NEXT

END