Door Lock

No automatic response

~5min read

DESCRIPTION

In some cases, the remote door lock central control functions are normal, but the automatic answer back function*1 of the hazard lights and/or the remote door lock buzzer does not operate. In this case, the signal outputs of the hazard lights and the remote door lock buzzer*1 from the main body ECU (multiplex network body ECU) may be malfunctioning.

  • *1: with Toyota Safety Sense P system

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • The remote door lock central control system and the key reminder system use the CAN communication system. Check the communication function by following the procedure described in the HOW TO PROCEED WITH TROUBLESHOOTING section. Perform troubleshooting of the remote door lock central control system only after confirming that the communication system operates normally.

    Click here

  • If the main body ECU (multiplex network body ECU) has been replaced, refer to the registration section.

    Click here

PROCEDURE

  1. READ VALUE USING TECHSTREAM (Hazard Answer Back, Wireless Buzzer Resp, Wireless Buzzer Vol)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON (IG).

(c) Turn on the Techstream.

(d) Select the following menus: Customize Setting / Wireless Door Lock.

(e) Select the setting by referring to the table below.

Remote Central Door Lock

Tester display

Description

Default setting

Setting

ECU

Hazard Answer Back

This function flashes the hazard lights once when the doors are locked using the remote control, and twice when the doors are unlocked using the remote control.

ON

0 : OFF, 1 : ON

Main body ECU (multiplex network body ECU)

Wireless Buzzer Resp

Remote door lock buzzer response*1

ON

0 : OFF, 1 : ON

Main body ECU (multiplex network body ECU)

Wireless Buzzer Vol

Remote door lock buzzer volume*1

Level5

0000: Level7, 0001: Level6, 0010: Level5, 0011: Level4, 0100: Level3, 0101: Level2, 0110: Level1, 0111: Level0

Main body ECU (multiplex network body ECU)

  • *1: with Toyota Safety Sense P system

Result:

Result

Proceed to

Both items are ON, except Level 0

A

Either item is OFF or Level 0

B

B

PERFORM CUSTOMIZE FUNCTION

A
  1. CHECK REMOTE DOOR LOCK FUNCTIONS

(a) Check the remote door lock central control function using the electronic key transmitter sub-assembly.

Result:

Result

Proceed to

Remote door lock/unlock operates normally

A

Remote door lock/unlock does not operate normally

B

B

REFER TO SYMPTOM TROUBLESHOOTING TABLE

A
  1. READ VALUE USING TECHSTREAM (FR Door Lock Pos, FL Door Lock Pos, RR-Door Lock Pos SW, RL-Door Lock Pos SW)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON (IG).

(c) Turn on the Techstream.

(d) Select the following menus: Body Electrical / Main Body / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Main Body > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

FR Door Lock Pos

Front Right Door Unlock Detection Switch Signal

LOCK or UNLOCK

LOCK: Front right door locked.

UNLOCK: Front right door unlocked.

-

FL Door Lock Pos

Front Left Door Unlock Detection Switch Signal

LOCK or UNLOCK

LOCK: Front left door locked.

UNLOCK: Front left door unlocked.

-

RR-Door Lock Pos SW

Rear RH door unlock detection switch signal

OFF or ON

OFF: Rear RH door locked

ON: Rear RH door unlocked

-

RL-Door Lock Pos SW

Rear LH door unlock detection switch signal

OFF or ON

OFF: Rear LH door locked

ON: Rear LH door unlocked

-

Body Electrical > Main Body > Data List

Tester display

FR Door Lock Pos

FL Door Lock Pos

RR-Door Lock Pos SW

RL-Door Lock Pos SW

OK:

The Techstream display changes correctly according to the lock/unlock operation.

NG

GO TO LIGHTING SYSTEM (go to door unlock detection switch circuit)

OK
  1. CHECK AUTOMATIC ANSWER BACK OPERATION

(a) Check the remote automatic answer back operation using the electronic key transmitter sub-assembly.

Result:

Result

Proceed to

Only the remote door lock buzzer automatic answer back does not operate (with Toyota Safety Sense P)

A

Only the hazard light automatic answer back does not operate

B

A

GO TO SMART KEY SYSTEM (for entry function) (exterior entry alarm and automatic answer back buzzer do not sound)

B
  1. CHECK HAZARD LIGHT OPERATION

(a) Check whether the hazard lights flash when the hazard switch is pressed.

OK:

The hazard lights flash.

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING SYSTEM (go to hazard switch circuit)