Operation Check
OPERATION CHECK
NOTE FOR THE FOLLOWING CHECKS
(a) Remote door lock/unlock function:
The remote door locking system only operates when the following 3 conditions are met:
(1) The ignition switch is in the OFF position.
(2) All doors are closed.
(3) The central door locking system operates correctly.
HINT:
The unlock function operates even when a door is open.
(b) The size of the remote door locking operating range may vary depending on conditions.
(1) The size of the operating range depends on the user and on how the electronic key transmitter is oriented.
(2) In some areas, the operating range of the remote door locking function may be limited by the shape of the vehicle body and by the influence of the surrounding environment.
(3) Because the electronic key transmitter uses weak radio waves, strong radio waves or electrical noise in the frequency used by the electronic key transmitter may reduce the operating range, and the remote control may not work.
(4) When the transmitter battery is weak, the operating range decreases and the remote control may not work.
HINT:
Leaving the electronic key transmitter in a place directly exposed to sunlight, such as on the instrument panel, may weaken the battery or cause other problems.
CHECK REMOTE DOOR LOCK FUNCTIONS
NOTICE:
The check procedure below assumes the vehicle has not been customized from its original configuration.
HINT:
- The switches described in this text are switches used to send signals. The switches are built into the electronic key transmitter.
- These functions must be checked against the operating range of the remote control.
(a) Make sure the vehicle is within an area where the remote control function can operate.
(b) Check the basic functions.
(1) Make sure the LED on the electronic key transmitter turns on and off 3 times when each switch is held down for 5 seconds.
HINT:
If the transmitter LED turns on and off once or twice but not a third time when the switch is held down for at least 5 seconds, the battery may be weak.
(2) Check whether all doors lock when the lock switch is pressed.
(3) Check that the driver door unlocks when the unlock switch is pressed once, and that all doors unlock when it is pressed twice within 5 seconds.
(c) Check the anti-repeat function.
(1) Hold down the lock or unlock switch on the electronic key transmitter and make sure the corresponding operation is performed only once and does not repeat continuously while the switch is held down. Then, make sure the operation works correctly when the switch is pressed repeatedly at 1-second intervals.
(d) Check the auto lock function.
(1) Make sure all doors automatically lock if none of them has been opened or locked within approximately 60 seconds after the doors are unlocked using the unlock switch.
(2) Make sure the auto lock function does not operate when a door has been opened within approximately 60 seconds after the doors are unlocked using the unlock switch.
(3) Make sure the auto lock function does not operate when all doors have been locked manually (such as with the key operation or by pressing the lock switch) within approximately 60 seconds after the doors are unlocked using the unlock switch.
(e) Check the switch security function.
(1) Make sure the doors cannot be locked/unlocked by operating a switch on an unregistered electronic key transmitter, but can be locked/unlocked by operating a switch on the registered electronic key transmitter.
(f) Check the door ajar warning buzzer function*2
(1) Check whether the remote door lock buzzer sounds for approximately 5 seconds when the lock switch is pressed and any door is ajar or open.
(g) Check the repeat function.
(1) Check whether all doors lock automatically 1 second after the lock switch is pressed while the driver door control is held in the unlock position.
(h) Check the automatic response function (hazard lights).
(1) Check that the hazard lights flash once at the same time as all doors lock when the lock switch is pressed.
(2) When the unlock switch is pressed, check that the hazard lights flash twice at the same time and that all doors unlock.
(i) Check the automatic response function (wireless door lock buzzer).*1
(1) When the lock switch is pressed, check that the buzzer sounds once at the same time as all doors unlock.
(2) When the unlock switch is pressed once, check that the buzzer sounds twice at the same time as the driver's door unlocks.
(j) Check that the door lock cancel function works when a door is open or ajar.
(1) When a door is open or ajar, check that the doors cannot be locked when the lock switch is operated.
HINT:
The doors can be unlocked even when a door is open or ajar.
(k) Check the remote reservation lock function.*1, *2
With one door open, press the lock switch on the electronic key transmitter assembly and check whether the doors lock when all doors are closed.
(l) Check the panic alarm control function.*1
With the alarm function active, press and hold the PANIC switch for at least 0.8 seconds. Check that the buzzer sounds, the headlights and tail lights flash, and the interior light stays on (with the light switch set to DOOR) for 60 seconds. Also check that the buzzer stops and the lights stop flashing when any switch on the transmitter is pressed.
(m) Check the door courtesy light function.
Click here![]()
(n) Check the power window open/close function.
Click here![]()
- *1: with Toyota Safety Sense P system
HINT:
*2: If the customization setting "Wireless Lock Function with Doors Open" is set to ON, the "Door Ajar Warning" will no longer operate. If the "Door Ajar Warning" is set to ON, the "Wireless Lock Function with Doors Open" will no longer operate. If both settings are set to ON, priority is given to the "Wireless Lock Function with Doors Open".