Heater / Air Conditioning

Installation

~8min read
010203040502518N·mlb·ft
Tightening torque found on this page

INSTALLATION

PROCEDURE

1. INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY

(a) Engage the claws to install the lower defroster nozzle assembly.

2. TEMPORARILY INSTALL THE AIR CONDITIONING UNIT ASSEMBLY

(a) Temporarily install the air conditioning unit assembly to the instrument panel reinforcement sub-assembly with 3 bolts.

3. INSTALL THE INSTRUMENT PANEL REINFORCEMENT SUB-ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY

NOTICE:

Be sure to support the air conditioning unit assembly during installation. Failure to do so may cause the air conditioning unit assembly support to break.

(a) Engage the guides to install the instrument panel reinforcement sub-assembly with the air conditioning unit assembly as shown in the illustration.

Install in this direction

-

-

(b) Connect the 2 connectors.

(c) Engage the clips.

(d) Install the 5 bolts.

Torque:

Bolt A:

25 N·m {255 kgf·cm, 18 ft·lbf}

Bolt B:

24 N·m {241 kgf·cm, 17 ft·lbf}

(e) Temporarily install the nut.

(f) Install the 2 bolts.

Torque:

25 N·m {255 kgf·cm, 18 ft·lbf}

4. CONNECT COOLER DRAIN HOSE

(a) Connect the cooler drain hose.

NOTICE:

If the cooler drain hose grommet is disconnected from the vehicle body when connecting the cooler drain hose, be sure to replace it with a new one. Failure to do so may cause water leakage.

*1

Cooler Drain Hose Grommet

5. INSTALL INSTRUMENT PANEL WIRE

(a) Engage the clips and hook to connect the instrument panel wire.

*a

Clip

*b

Hook

(b) Install the instrument panel junction block assembly with the main body ECU using the bolt and nut.

Torque:

8 N·m {82 kgf·cm, 71 in·lbf}

(c) Install the 4 wire harness ground wires with the 4 bolts.

Torque:

Bolt A:

10.5 N·m {107 kgf·cm, 8 ft·lbf}

Bolt B (part number 90119-06995):

10.5 N·m {107 kgf·cm, 8 ft·lbf}

Bolt B (part number 90119-06915):

8.5 N·m {87 kgf·cm, 75 in·lbf}

Bolt B (part number 90119-06A07):

10 N·m {102 kgf·cm, 7 ft·lbf}

(d) Install the bolt and screw.

Torque:

Bolt:

8 N·m {82 kgf·cm, 71 in·lbf}

(e) Connect each connector.

6. INSTALL INSTRUMENT PANEL ON NO. 3 INSTRUMENT PANEL REINFORCEMENT SUB-ASSEMBLY

(a) Install the No. 3 instrument panel brace sub-assembly with the bolt and nut.

Torque:

Bolt:

10 N·m {102 kgf·cm, 7 ft·lbf}

Nut:

6 N·m {61 kgf·cm, 53 in·lbf}

(b) Engage the claws and clips.

7. INSTALL NO. 2 INSTRUMENT PANEL REINFORCEMENT SUB-ASSEMBLY

(a) Install the No. 2 instrument panel reinforcement sub-assembly with the bolt and nut.

Torque:

Bolt:

20 N·m {204 kgf·cm, 15 ft·lbf}

Nut:

18 N·m {184 kgf·cm, 13 ft·lbf}

(b) Temporarily install the screw.

HINT:

Do not fully tighten the screw.

(c) Install the ground wire with its bolt.

Torque:

10.5 N·m {107 kgf·cm, 8 ft·lbf}

(d) Engage the clips to connect the wire harness.

8. INSTALL NO. 1 INSTRUMENT PANEL REINFORCEMENT SUB-ASSEMBLY

(a) Install the No. 1 instrument panel reinforcement sub-assembly with the bolt and nut.

Torque:

Bolt:

20 N·m {204 kgf·cm, 15 ft·lbf}

Nut:

18 N·m {184 kgf·cm, 13 ft·lbf}

(b) Temporarily install the screw.

HINT:

Do not fully tighten the screw.

(c) Engage the clips to connect the wire harness.

(d) Install the relay block assembly with the 2 nuts.

Torque:

8 N·m {82 kgf·cm, 71 in·lbf}

(e) Install the bolt to connect the ground wire.

Torque:

10.5 N·m {107 kgf·cm, 8 ft·lbf}

9. INSTALL AIR CONDITIONING UNIT ASSEMBLY

(a) Tighten the 3 bolts, 2 screws and nut in the order shown in the illustration to install the air conditioning unit.

Torque:

9.8 N·m {100 kgf·cm, 87 in·lbf}

10. INSTALL NO. 1 REAR AIR DUCT

(a) Engage the claws to install the No. 1 rear air duct.

Install in this direction

11. INSTALL NO. 2 REAR AIR DUCT

(a) Engage the claws to install the No. 2 rear air duct as shown in the illustration.

Install in this direction

12. INSTALL NO. 3 REAR AIR DUCT

(a) Engage the claws to install the No. 3 rear air duct as shown in the illustration.

Install in this direction

13. INSTALL NO. 4 REAR AIR DUCT

(a) Engage the claws to install the No. 4 rear air duct as shown in the illustration.

Install in this direction

(b) Install the front floor carpet assembly to its original position as shown in the illustration.

Install in this direction

(c) Engage the clips.

(d) Install the clip.

(e) Install the 2 front floor carpet clips.

14. INSTALL NO. 5 REAR AIR DUCT

(a) Engage the claws to install the No. 5 rear air duct as shown in the illustration.

Install in this direction

15. INSTALL NO. 6 REAR AIR DUCT

(a) Engage the claws to install the No. 6 rear air duct as shown in the illustration.

Install in this direction

16. INSTALL NO. 3 INSTRUMENT PANEL INSULATOR PAD

(a) Engage the clips to install the No. 3 instrument panel insulator pad.

(b) Install the front floor carpet assembly to its original position as shown in the illustration.

Install in this direction

(c) Engage the clips.

(d) Install the clip.

(e) Install the 2 front floor carpet clips.

17. INSTALL COOLER THERMISTOR (CABIN TEMPERATURE SENSOR)

(a) Connect the suction hose and connector to install the cooler thermistor (cabin temperature sensor).

18. INSTALL RH ECU INTEGRATION BOX

Click here

19. INSTALL FRONT WIPER RELAY ASSEMBLY

Click here

20. INSTALL STEERING COLUMN ASSEMBLY

Click here

21. INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Click here

22. INSTALL LH FRONT SEAT ASSEMBLY

Click here

23. INSTALL RH FRONT SEAT ASSEMBLY

HINT:

Perform the same procedure as for the left side.

24. CONNECT COOLER REFRIGERANT LIQUID TUBE A

(a) Remove the vinyl tape from the cooler refrigerant liquid tube A.

(b) Apply sufficient compressor oil to a new O-ring and the connection surface of the cooler refrigerant liquid tube A.

Compressor oil:

ND-OIL 12 or equivalent

(c) Install the O-ring to the cooler refrigerant liquid tube A.

NOTICE:

Keep the O-ring and O-ring connection surface free of foreign matter.

(d) Install the bolt and cooler refrigerant liquid tube A.

25. CONNECT SUCTION TUBE SUB-ASSEMBLY

(a) Remove the vinyl tape from the suction tube sub-assembly.

(b) Apply sufficient compressor oil to a new O-ring and the connection surface of the suction tube sub-assembly.

Compressor oil:

ND-OIL 12 or equivalent

(c) Install the O-ring to the suction tube sub-assembly.

NOTICE:

Keep the O-ring and O-ring connection surface free of foreign matter.

(d) Connect the suction tube sub-assembly.

(e) Rotate the hook-type connector as shown in the illustration.

Install in this direction

(f) Properly insert the hose fitting into the connection port and tighten the bolt.

Torque:

9.8 N·m {100 kgf·cm, 87 in·lbf}

26. CONNECT HEATER WATER INLET HOSE

(a) Connect the heater water inlet hose with the (pink) marking facing up, and engage the clamp in the area shown in the illustration.

NOTICE:

Proceed carefully to avoid damaging the heater water inlet hose.

*a

View A

*b

Marking (pink)

*c

Clip installation angle (120°)

27. CONNECT HEATER WATER OUTLET HOSE

(a) Connect the heater water outlet hose with the marking facing up (blue), engage the clip in the area shown in the illustration.

NOTICE:

Proceed carefully to avoid damaging the heater water outlet hose.

*a

View A

*b

Marking (blue)

*c

Clip installation angle (120°)

28. INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY

Click here

29. INSTALL LH COWL BODY MOUNTING REINFORCEMENT

Click here

30. INSTALL RH COWL BODY MOUNTING REINFORCEMENT

Click here

31. INSTALL LH WATERPROOF PROTECTIVE PLATE

Click here

32. INSTALL HEATER AIR DUCT SPLASH SHIELD SEAL NO. 1

Click here

33. INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY

Click here

34. ADD ENGINE COOLANT

Click here

35. CHECK FOR ENGINE COOLANT LEAK

Click here

36. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Click here

37. WARM UP ENGINE

Click here

38. CHECK FOR REFRIGERANT LEAK

Click here

39. SERVO MOTOR INITIALIZATION

Click here