Inspection On Vehicle
INSPECTION ON VEHICLE
PRECAUTION / NOTICE / HINT
NOTICE:
If the battery is low or the engine is hard to start, recharge the battery and repeat the checks before returning the vehicle to the customer.
PROCEDURE
1. CHECK BATTERY CONDITION
(a) Make sure the battery is not damaged or deformed. If there is significant damage, deformation or leakage, replace the battery.
(b) Check the electrolyte level in each cell.
(1) For maintenance-free batteries:
- If the electrolyte level is below the minimum level, replace the battery.
- If the electrolyte level is above the minimum level, check the battery voltage while the engine is cranked by the starter. If the voltage is below 9.6 V, recharge or replace the battery.
HINT:
Before checking the battery voltage, turn off all electrical systems (headlights, blower motor, rear defogger, etc.).
(2) For batteries with maintenance:
- If the electrolyte level is below the minimum level, add distilled water to each cell. Then recharge the battery and check the electrolyte specific gravity.
Standard electrolyte specific gravity:
1.25 minimum at 20 °C
- If the electrolyte level is above the minimum level, check the battery voltage while the engine is cranked by the starter. If the battery voltage is below 9.6 V, recharge or replace the battery.
HINT:
Before checking the battery voltage, turn off all electrical systems (headlights, blower motor, rear defogger, etc.).
(c) Check the voltage.
(1) Turn the ignition switch OFF and turn on the headlights for 20 to 30 seconds. This removes the surface charge from the battery.
(2) Measure the battery voltage and compare it with the value(s) shown in the table below.
Standard voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
Positive (+) terminal - Negative (-) terminal |
20 °C |
12.3 V minimum |
If the result does not meet the specification, recharge or replace the battery.
2. CHECK BATTERY TERMINALS
(a) Make sure the battery terminals are not loose or corroded.
If a terminal is loose or corroded, tighten or clean the terminal.
Torque:
Positive (+) battery terminal:
5.4 N·m {55 kgf·cm, 48 in·lbf}
Negative (-) battery terminal:
5.4 N·m {55 kgf·cm, 48 in·lbf}
3. CHECK FUSES
(a) Measure the resistance of each fuse for the charging system.
HINT:
The fuses shown in the system diagram are related to the charging system.
Standard resistance:
Below 1 Ω
- If the result does not meet the specification, replace the fuse.
4. CHECK FAN AND ALTERNATOR V-RIBBED BELT
Click here![]()
5. CHECK ALTERNATOR ASSEMBLY WIRING WITH REGULATOR
(a) Perform a visual inspection of the alternator assembly wiring.
(1) Make sure the wiring is in good condition.
6. CHECK FOR ABNORMAL NOISE
(a) Listen for abnormal noise coming from the alternator assembly.
(1) Make sure the alternator assembly does not make any abnormal noise while the engine is running.
If noise is heard, inspect the alternator assembly.
Click here![]()
7. CHECK CHARGE WARNING LIGHT
(a) Turn the ignition switch to ON.
(b) Make sure the charge warning light comes on.
(c) Start the engine and check that the charge warning light goes off.
If the charge warning light does not operate as specified, troubleshoot the charge warning light circuit.
Click here
![]()
8. CHECK CHARGING CIRCUIT (ENGINE NOT RUNNING)
(a) Connect a voltmeter and an ammeter to the charging circuit as follows. HINT: If no battery/alternator tester is available, connect the tester to the charging circuit according to the manufacturer's instructions. (1) Disconnect the cable from terminal B of the alternator assembly, then connect it to the negative (-) cable of the ammeter. (2) Connect the positive (+) cable of the ammeter to terminal B of the alternator assembly. (3) Connect the positive (+) cable of the voltmeter to terminal B of the alternator assembly. (4) Connect the negative (-) cable of the voltmeter to ground. |
|
(b) Check the charging circuit.
(1) Maintain engine speed at 2,000 rpm and check the values shown on the ammeter and voltmeter.
Standard current:
10 A minimum
Standard voltage:
13,2 à 14,8 V
If the result does not meet the specification, repair or replace the alternator assembly.
HINT:
If the battery is not fully charged, the ammeter may sometimes show a value higher than the standard current.
9. CHECK CHARGING CIRCUIT (ENGINE RUNNING WITH LOAD)
(a) Run the engine at 2,000 rpm, turn on the headlights on high beam, and set the heater blower switch to "HI".
(b) Check the value shown on the ammeter.
Standard current:
30 A minimum
If the result does not meet the specification, repair or replace the alternator assembly.
HINT:
If the battery is fully charged, the displayed value may sometimes be lower than the standard value. In this case, increase the electrical load (operate the windshield wipers, rear window defogger, etc.) and check the ammeter value again.
