Ambient Illumination Light Circuit
DESCRIPTION
The main body ECU (multiplex network body ECU) controls the operation of the following lights:
- Center tray illumination light (No. 1 interior illumination light assembly)
- Front Door Ambient Illumination Light
- Front door ambient illumination light LH (Front door trim board sub-assembly LH)
- Front door ambient illumination light RH (Front door trim board sub-assembly RH)
WIRING DIAGRAM
NOTICE:
- Inspect the fuses for circuits related to this system before performing the following procedure.
- Before replacing the main body ECU (multiplex network body ECU), refer to Registration.*1
for HEV Model: Click here
.gif)
for Gasoline Model: Click here
.gif)
- *1: w/ Smart Key System
PROCEDURE
PERFORM ACTIVE TEST USING GTS
(a) Perform the Active Test according to the display on the GTS.
Body Electrical > Main Body > Active TestTester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
Front Footwell Lights |
|
OFF or ON |
- |
Front Footwell Lights
Result | Proceed to |
|---|---|
OK |
A |
NG (Center tray illumination light (No. 1 interior illumination light assembly) light does not come on) |
B |
NG (Front door ambient illumination light RH (Front door trim board sub-assembly RH) do not come on) |
C |
NG (Front door ambient illumination light LH (Front door trim board sub-assembly LH) do not come on) |
D |
NG (All illuminations do not come on) |
E |
| A | USE SIMULATION METHOD TO CHECK |
| C | GO TO STEP 5 |
| D | GO TO STEP 8 |
| E | GO TO STEP 11 |
|
INSPECT CENTER TRAY ILLUMINATION LIGHT (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY)
Click here ![]()
| NG | REPLACE CENTER TRAY ILLUMINATION LIGHT (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY) |
|
CHECK HARNESS AND CONNECTOR (CENTER TRAY ILLUMINATION LIGHT (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY) - POWER DISTRIBUTION BOX ASSEMBLY)
(a) Disconnect the 8B and 8C power distribution box assembly connectors.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
I225- 2(B) - 8B-44 |
Always |
Below 1 Ω |
I225-1 (E) - 8C-18 |
Always |
Below 1 Ω |
I225-2 (B) or 8B-44 - Body ground |
Always |
10 kΩ or higher |
I225-1 (E) or 8C-18 - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT POWER DISTRIBUTION BOX ASSEMBLY
*a |
Component without harness connected (Power Distribution Box Assembly) |
- |
- |
(a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
Click here ![]()
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
8C-18 - MB-16 (FSPT) |
Always |
Below 1 Ω |
| OK | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG | REPLACE POWER DISTRIBUTION BOX ASSEMBLY |
INSPECT FRONT DOOR AMBIENT ILLUMINATION LIGHT RH (FRONT DOOR TRIM BOARD SUB-ASSEMBLY RH)
Click here ![]()
| NG | REPLACE FRONT DOOR AMBIENT ILLUMINATION LIGHT RH (FRONT DOOR TRIM BOARD SUB-ASSEMBLY RH) |
|
CHECK HARNESS AND CONNECTOR (FRONT DOOR AMBIENT ILLUMINATION LIGHT RH (FRONT DOOR TRIM BOARD SUB-ASSEMBLY RH) - POWER DISTRIBUTION BOX ASSEMBLY)
(a) Disconnect the 8B and 8C power distribution box assembly connectors.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
K6- 2(+) - 8B-44 |
Always |
Below 1 Ω |
K6-1 (-) - 8C-18 |
Always |
Below 1 Ω |
K6-2 (+) or 8B-44 - Body ground |
Always |
10 kΩ or higher |
K6-1 (-) or 8C-18 - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT POWER DISTRIBUTION BOX ASSEMBLY
*a |
Component without harness connected (Power Distribution Box Assembly) |
- |
- |
(a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
Click here ![]()
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
8C-18 - MB-16 (FSPT) |
Always |
Below 1 Ω |
| OK | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG | REPLACE POWER DISTRIBUTION BOX ASSEMBLY |
INSPECT FRONT DOOR AMBIENT ILLUMINATION LIGHT LH (FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH)
Click here ![]()
| NG | REPLACE FRONT DOOR AMBIENT ILLUMINATION LIGHT RH (FRONT DOOR TRIM BOARD SUB-ASSEMBLY RH) |
|
CHECK HARNESS AND CONNECTOR (FRONT DOOR AMBIENT ILLUMINATION LIGHT LH (FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH) - POWER DISTRIBUTION BOX ASSEMBLY)
(a) Disconnect the 8B and 8C power distribution box assembly connectors.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
L5- 2(+) - 8B-44 |
Always |
Below 1 Ω |
L5-1 (-) - 8C-18 |
Always |
Below 1 Ω |
L5-2 (+) or 8C-18 - Body ground |
Always |
10 kΩ or higher |
L5-1 (-) or 8C-18 - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT POWER DISTRIBUTION BOX ASSEMBLY
*a |
Component without harness connected (Power Distribution Box Assembly) |
- |
- |
(a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
Click here ![]()
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
8C-18 - MB-16 (FSPT) |
Always |
Below 1 Ω |
| OK | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG | REPLACE POWER DISTRIBUTION BOX ASSEMBLY |
CHECK HARNESS AND CONNECTOR (POWER SOURCE - POWER DISTRIBUTION BOX ASSEMBLY)
(a) Disconnect the 8H power distribution box assembly connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
8H-1 - Body ground |
Ignition switch off |
11 to 14 V |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK POWER DISTRIBUTION BOX ASSEMBLY
*a |
Component without harness connected (Power Distribution Box Assembly) |
- |
- |
(a) Disconnect the 8B power distribution box assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
8H-1 - 8B-44 |
Always |
Below 1 Ω |
| NG | REPLACE POWER DISTRIBUTION BOX ASSEMBLY |
|
INSPECT POWER DISTRIBUTION BOX ASSEMBLY
*a |
Component without harness connected (Power Distribution Box Assembly) |
- |
- |
(a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
Click here ![]()
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
8C-18 - MB-16 (FSPT) |
Always |
Below 1 Ω |
| OK | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG | REPLACE POWER DISTRIBUTION BOX ASSEMBLY |