Rear Door Courtesy Switch Circuit
DESCRIPTION
The main body ECU (multiplex network body ECU) detects the condition of the rear door courtesy light switch assembly.
WIRING DIAGRAM
NOTICE:
Before replacing the main body ECU (multiplex network body ECU), refer to Registration.*1
for HEV Model: Click here ![]()
for Gasoline Model: Click here ![]()
- *1: w/ Smart Key System
PROCEDURE
READ VALUE USING GTS
(a) Read the Data List according to the display on the GTS.
Body Electrical > Main Body > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
RR Door Courtesy Switch Status |
Rear door courtesy light switch assembly (RH) signal |
CLOSE or OPEN |
CLOSE: Rear door RH closed OPEN: Rear door RH open |
- |
RL Door Courtesy Switch Status |
Rear door courtesy light switch assembly (LH) signal |
CLOSE or OPEN |
CLOSE: Rear door LH closed OPEN: Rear door LH open |
- |
Tester Display |
|---|
RR Door Courtesy Switch Status |
RL Door Courtesy Switch Status |
OK:
Normal conditions listed above are displayed.
Result | Proceed to |
|---|---|
OK |
A |
NG ("RL Door Courtesy Switch Status" is not normal) |
B |
NG ("RR Door Courtesy Switch Status" is not normal) |
C |
| A | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| C | GO TO STEP 5 |
|
INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH)
Click here ![]()
| NG | REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH |
|
CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH) - POWER DISTRIBUTION BOX ASSEMBLY)
(a) Disconnect the 8F power distribution box assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
O31-1 - 8F-28 |
Always |
Below 1 Ω |
O31-1 - Body ground |
Always |
10 kΩ or higher |
8F-28 - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT POWER DISTRIBUTION BOX ASSEMBLY
*a |
Component without harness connected (Power Distribution Box Assembly) |
- |
- |
(a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
Click here ![]()
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
8F-28 - MB-6 (LCTY) |
Always |
Below 1 Ω |
| OK | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG | REPLACE POWER DISTRIBUTION BOX ASSEMBLY |
INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (RH)
Click here ![]()
| NG | REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (RH) |
|
CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (RH) - POWER DISTRIBUTION BOX ASSEMBLY)
(a) Disconnect the 8F power distribution box assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
O34-1 - 8F-1 |
Always |
Below 1 Ω |
O34-1 - Body ground |
Always |
10 kΩ or higher |
8F-1 - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT POWER DISTRIBUTION BOX ASSEMBLY
*a |
Component without harness connected (Power Distribution Box Assembly) |
- |
- |
(a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
Click here ![]()
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
8F-1 - MB-1 (RCTY) |
Always |
Below 1 Ω |
| OK | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG | REPLACE POWER DISTRIBUTION BOX ASSEMBLY |