Push Start Switch Illumination Circuit
DESCRIPTION
The illuminated entry system controls the push start switch illumination.
WIRING DIAGRAM
for HEV Model
for Gasoline Model
NOTICE:
Before replacing the certification ECU (smart key ECU assembly), refer to Registration.*1
for HEV Model: Click here ![]()
for Gasoline Model: Click here ![]()
- *1: w/ Smart Key System
PROCEDURE
CHECK VEHICLE TYPE
(a) Check vehicle type.
Result | Proceed to |
|---|---|
for HEV Model |
A |
for Gasoline Model |
B |
| B | GO TO STEP 5 |
|
PERFORM ACTIVE TEST USING GTS
(a) Perform the Active Test according to the display on the GTS.
Body Electrical > Smart Key > Active TestTester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
Start SW Light Power Supply |
Push start switch illumination |
OFF or ON |
- |
Start SW Light Power Supply
OK:
Push start switch illumination comes on.
| OK | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
INSPECT PUSH START SWITCH
Click here ![]()
| NG | REPLACE PUSH START SWITCH |
|
CHECK HARNESS AND CONNECTOR (PUSH START SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
(a) Disconnect the I222 certification ECU (smart key ECU assembly) connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
I280-5 (SWIL) - I222-20 (SWIL) |
Always |
Below 1 Ω |
I280-3 (GND) - I222-30 (AGND) |
Always |
Below 1 Ω |
I280-5 (SWIL) or I222-20 (SWIL) - Body ground |
Always |
10 kΩ or higher |
I280-3 (GND) or I222-30 (AGND) - Body ground |
Always |
10 kΩ or higher |
| OK | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
PERFORM ACTIVE TEST USING GTS
(a) Perform the Active Test according to the display on the GTS.
Body Electrical > Smart Key > Active TestTester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
Start SW Light Power Supply |
Push start switch illumination |
OFF or ON |
- |
Start SW Light Power Supply
OK:
Push start switch illumination comes on.
| OK | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
INSPECT PUSH START SWITCH
Click here ![]()
| NG | REPLACE PUSH START SWITCH |
|
CHECK HARNESS AND CONNECTOR (PUSH START SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
(a) Disconnect the I222 certification ECU (smart key ECU assembly) connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
I35-5 (SWIL) - I222-20 (SWIL) |
Always |
Below 1 Ω |
I35-3 (GND) - I222-30 (AGND) |
Always |
Below 1 Ω |
I35-5 (SWIL) or I222-20 (SWIL) - Body ground |
Always |
10 kΩ or higher |
I35-3 (GND) or I222-30 (AGND) - Body ground |
Always |
10 kΩ or higher |
| OK | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |