Interior body assembly work

Crash sensors for airbag

6steps
~36min
2/5difficulty
0102030405097N·mlb·ft
Tightening torque found on this page
Done 0 of 6

Installation location overview - Crash sensors for airbag


Note

Installation location overview shows a 2-door vehicle.

VW UP. Karosserie-Montagearbeiten Innen

  1. Crash sensor for driver side front airbag -G283-
    • Installation location: in vehicle center on lock carrier
    • Remove and install
  2. Bolt
    • 9 N·m
  3. Crash sensor for passenger side airbag -G180-
    • Installation location, 2-door: below door trim panel
    • Installation location, 4-door: below sill trim
    • Remove and install
    • Precautions when handling the crash sensors (pressure sensors) for front side airbags
  4. Bolt
    • 2-door: 2 bolts
    • 2-door: 1 N·m
    • 4-door: 1 bolt
    • 4-door: 9 N·m
  5. Crash sensor for driver side airbag -G179-
    • Installation location, 2-door: below door trim panel
    • Installation location, 4-door: below sill trim
    • Remove and install
    • Precautions when handling the crash sensors (pressure sensors) for front side airbags
  6. Bolt
    • 2-door: 2 bolts
    • 2-door: 1 N·m
    • 4-door: 1 bolt
    • 4-door: 9 N·m

Removing and installing crash sensor for front airbag


Note

Despite its designation, the crash sensor for driver side front airbag -G283- is installed in the vehicle center.

Removing


WARNING!

Observe the safety regulations for pyrotechnic components.

- On e-up! vehicles, disconnect service plug for high-voltage system -TW-.

- Disconnect the battery ground cable with ignition switched on → Electrical system.

- Open the hood.

VW UP. Karosserie-Montagearbeiten Innen

- Unscrew bolt -1- and remove crash sensor for driver side front airbag -G283- -2-.


WARNING!

Before handling pyrotechnic components (for example, disconnecting the electrical connector), the person handling them must "discharge static electricity". To do this, briefly touch the door striker plate, for example.

- Pull out the connector lock and press it down, disconnect the electrical connector -3- from the crash sensor for driver side front airbag -G283- -2-.

Installing


WARNING!

  • Observe the safety regulations for pyrotechnic components.
  • Before handling pyrotechnic components (for example, connecting the electrical connector), the person handling them must "discharge static electricity". For example, briefly touch the door striker.

Installation is carried out in the reverse order, observing the following:


Note

  • Make sure that the electrical connectors are pushed on as far as they will go and audibly engage.
  • Make sure that the wiring is not pinched.


WARNING!

The battery must be connected with the ignition switched on. Improper repair work on pyrotechnic components (for example airbags or belt tensioners) can cause unintended deployment after the battery is connected. No person may be inside the vehicle cabin when connecting the battery.

VW UP. Karosserie-Montagearbeiten Innen

- On e-up! vehicles, connect the service plug for high-voltage system -TW-.

- Connect the battery ground cable with ignition switched on → Electrical system.


Note

If the airbag warning lamp -K75- signals a fault after installation, the fault memory must be read out, cleared and read out again → Vehicle diagnostic tester.

Installation notes: e.g. tightening torques, replacing components

VW UP. Karosserie-Montagearbeiten Innen

Removing and installing crash sensor for front side airbag

Crash sensor for driver side airbag -G179- / crash sensor for passenger side airbag -G180-

Removing, 2-door


WARNING!

  • Observe the safety regulations for pyrotechnic components.
  • Observe the precautions for the crash sensors (pressure sensors) for front side airbags.

- On e-up! vehicles, disconnect service plug for high-voltage system -TW-.

- Disconnect the battery ground cable with ignition switched on → Electrical system.

VW UP. Karosserie-Montagearbeiten Innen

- Remove door trim panel.


WARNING!

Before handling pyrotechnic components (for example, disconnecting the electrical connector), the person handling them must "discharge static electricity". To do this, briefly touch the door striker plate, for example.

- Pull out connector lock -5- in direction of -arrow- and press down, disconnect electrical connector -4- from crash sensor.

- Unscrew bolts -1, 3- and remove crash sensor -2- for side airbag.

Installation, 2-door


WARNING!

  • Observe the safety regulations for pyrotechnic components.
  • Observe the precautions for the crash sensors (pressure sensors) for front side airbags.
  • Before handling pyrotechnic components (for example, connecting the electrical connector), the person handling them must "discharge static electricity". For example, briefly touch the door striker.

Installation is carried out in the reverse order, observing the following:


Note

  • Make sure that the electrical connectors are pushed on as far as they will go and audibly engage.
  • For trouble-free function of the crash sensor (pressure sensor), the door seal must be ensured.
  • All components (for example cover, speaker, door trim) must be correctly installed.
  • The retaining clips for the door trim seal the system. Replace the retaining clips if necessary.
  • Make sure that the wiring is not pinched.


WARNING!

The battery must be connected with the ignition switched on. Improper repair work on pyrotechnic components (for example airbags or belt tensioners) can cause unintended deployment after the battery is connected. No person may be inside the vehicle cabin when connecting the battery.

VW UP. Karosserie-Montagearbeiten Innen

- On e-up! vehicles, connect the service plug for high-voltage system -TW-.

- Connect the battery ground cable with ignition switched on → Electrical system.


Note

If the airbag warning lamp -K75- signals a fault after installation, the fault memory must be read out, cleared and read out again → Vehicle diagnostic tester.

Installation notes: e.g. tightening torques, replacing components

Removal, 4-door


WARNING!

  • Observe the safety regulations for pyrotechnic components.
  • Observe precautions for front side airbag crash sensors.
VW UP. Karosserie-Montagearbeiten Innen

- On e-up! vehicles, disconnect service plug for high-voltage system -TW-.

- Disconnect the battery ground cable with ignition switched on → Electrical system.

- Remove sill trim, 4-door.


WARNING!

Before handling pyrotechnic components (for example, disconnecting the electrical connector), the person handling them must "discharge static electricity". To do this, briefly touch the door striker plate, for example.

VW UP. Karosserie-Montagearbeiten Innen

- Unlock connector lock and disconnect electrical connector -3- from crash sensor -2-.

- Unscrew bolt -1- and remove crash sensor -2- for side airbag.

Installation, 4-door


WARNING!

  • Observe the safety regulations for pyrotechnic components.
  • Observe precautions for front side airbag crash sensors.
  • Before handling pyrotechnic components (for example, connecting the electrical connector), the person handling them must "discharge static electricity". For example, briefly touch the door striker.

Installation is carried out in the reverse order, observing the following:


Note

  • Make sure that the electrical connectors are pushed on as far as they will go and audibly engage.
  • Make sure that the wiring is not pinched.


WARNING!

The battery must be connected with the ignition switched on. Improper repair work on pyrotechnic components (for example airbags or belt tensioners) can cause unintended deployment after the battery is connected. No person may be inside the vehicle cabin when connecting the battery.

VW UP. Karosserie-Montagearbeiten Innen

- On e-up! vehicles, connect the service plug for high-voltage system -TW-.

- Connect the battery ground cable with ignition switched on → Electrical system.


Note

If the airbag warning lamp -K75- signals a fault after installation, the fault memory must be read out, cleared and read out again → Vehicle diagnostic tester.

Installation notes: e.g. tightening torques, replacing components

VW UP. Karosserie-Montagearbeiten Innen