Body Exterior, Doors, Roof & Vehicle Security

Cab Mounting Insulator

3steps
~18min
4/5difficulty
Done 0 of 3

Exploded View

Cab mounting insulator (1st) Cab mounting insulator (2nd) Cab mounting insulator (3rd)
Cab mounting insulator (4th) Front bumper cross member Rear engine mounting cross member
Chipping protector
: N·m (kg-m, ft-lb)

Removal and Installation

PREPARATION FOR SEPARATION OF FRAME ASSEMBLY AND BODY ASSEMBLY

Set arms of 2-pole lift to lifting point of frame assembly. Refer to 2-Pole Lift.

Therefore, the vehicle position must be an appropriate position to perform for both operations.

Remove/Disconnect the Parts Installed in Vehicle Front Part

Perform the following works.

  • Remove engine under cover. Refer to Removal and Installation.

  • Discharge refrigerant. Refer to Recycle Refrigerant.

  • Drain brake fluid. Refer to Draining.

  • Drain engine coolant. Refer to ENGINE COOLANT : Draining.

  • Drain A/T fluid. Refer to Changing.

  • Remove all tires and wheels. Refer to ROAD WHEEL TIRE : Removal & Installation.

  • Remove fender protector (LH and RH). Refer to Removal and Installation.

  • Remove front bumper fascia and front bumper retainer upper. Refer to Removal and Installation (OFF ROAD MODEL) or Removal and Installation (CITY MODEL).

  • Disconnect brake tubes inside front fender (LH and RH). Refer to Removal and Installation.

  • Disconnect front wheel sensor harness connectors. Refer to Removal and Installation.

  • Disconnect shock absorber harness connector (with air suspension models). Refer to Removal and Installation.

  • Disconnect engine room harness connectors and remove harness clips from engine assembly (engine RH side). Refer to Harness Layout.

  • Remove 12V battery and battery tray. Refer to Removal and Installation.

  • Remove heater hose from front heater pipe assembly. Refer to Removal and Installation.

  • Remove radiator hose (upper and lower). Refer to RADIATOR : Removal & Installation.

  • Remove radiator reservoir tank. Refer to RADIATOR : Exploded View.

  • Remove air cleaner cover and air duct 1. Refer to Removal and Installation.

  • Remove air inlet tube 1 and 2 from charge air cooler. Refer to Removal & Installation.

  • Remove A/T fluid cooler hose A and B from A/T fluid cooler tube assembly. Refer to Removal and Installation.

  • Remove A/C low-pressure flexible hose from A/C low-pressure pipe. Refer to Removal and Installation.

  • Remove A/C high-pressure flexible hose from condenser. Refer to Removal and Installation.

  • Separate lower joint from steering shaft. Refer to Removal and Installation.

Remove/Disconnect the Parts Installed in Vehicle Center Part

Disconnect harness connector on frame assembly RH center side.

  1. Remove fixing clip and disengage fixing pawl, and then remove harness connector protector.

    : Clip
    : Pawl
    : vehicle front
  2. Remove harness bracket bolts , and then remove harness brackets.

    : vehicle front
  3. Disconnect harness connector.

Remove/Disconnect the Parts Installed in Vehicle Rear Part

Perform the following works.

  • Remove rear bumper fascia. Refer to Removal and Installation.

  • Remove rear wheel house protector (LH and RH). Refer to Removal and Installation.

  • Remove fuel filler base mask. Refer to Removal and Installation.

  • Remove fuel filler tube protector 1 and fuel filler tube 1 mounting bolts. Refer to FUEL TANK : Removal & Installation.

  • Disconnect air suspension duct assembly from air suspension (LH and RH) duct assembly (with air suspension models). Refer to Removal and Installation.

REMOVAL

Install all tires and wheels. Refer to ROAD WHEEL TIRE : Removal & Installation.

Unload the vehicle from lift.

Set arms of 2-pole lift to lifting point of body assembly.

Apply matching tapes (A) to all tires.

Remove all cab mounting insulator mounting bolts.

Slowly lift up the body assembly using 2-pole lift.

Remove cab mounting insulator (2nd) and (4th) mounting nuts.

Remove cab mounting insulator.

INSTALLATION

Note the following items, and then install in the reverse order of removal.