Engine Mechanical K9K

High pressure supply pump

In this manual: Engine Mechanical K9K
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~3min read
03060901201507052N·mlb·ft
Tightening torque found on this page

Exploded View

1. High pressure supply pump protector

1. High pressure supply pump protector 2. High pressure supply pump

Removal and Installation: N·m (kg-m, ft-lb)


Removal and Installation

REMOVAL

CAUTION:
• Be sure to read “Precautions for Diesel Equipment”. Refer to EM-263, "Precaution for Diesel Equipment". • Wait until the fuel temperature drops before carrying out any work. • Order the special high pressure injection circuit plug kit.

• In case of the replacement of the high pressure supply pump sprocket, please apply the following tightening torque:

: 70 N·m


1. Disconnect the battery cable from the negative terminal.

1. Disconnect the battery cable from the negative terminal. 2. Remove cowl top extension. Refer to EXT-20, "Exploded View". 3. Remove turbocharger air inlet pipe. Refer to EM-280, "Exploded View". 4. Remove air inlet tube assembly and air inlet tube. Refer to EM-281, "Exploded View". 5. Remove the timing belt. Refer to EM-302, "Exploded View". 6. Remove the neck located on the fuel rail, 7. Remove the oil level gauge guide and plug the hole. 8. Remove high pressure protection cover. Refer to EM-294, "Exploded View".

9. Carefully disconnect:

• The connectors from the flow actuator, • The connectors from the fuel temperature sensor, • On the pump, the fuel supply and return pipes.

• The return pipe connecting the injectors with the pump.

10. Remove the injection tube connecting the pump to the rail. Refer to EM-294, "Exploded View". 11. Plug all the holes of the injection circuit.

12. Remove the three mounting bolts from the high pressure supply pump then remove it.

INSTALLATION

1. Install the pump then position the mounting bolts without tightening them. 2. Before fitting the new injection tube, lightly lubricate the nut threads with the oil from the sachet provided in the new parts kit.

3. Refit the injection tube, to do this:

• remove the protective plugs, • insert the injection tube olive into the taper of the high pressure pump outlet,
• insert the injection tube olive into the taper of the high pressure rail inlet.

4. Finger tighten the nuts of the injection tube starting with the one located on the rail side.

5. Tighten the mounting bolts on the high pressure pump.

6. Tighten the injection tube nut.: 21 N·m


6. Tighten the injection tube nut.

7. Refit high pressure supply pump protector.: 24 N·m


7. Refit high pressure supply pump protector.

• Be sure disk rubber (1) is touching bolt head of high pressure supply pump (2) as shown in the figure. • Tighten bolt with holding protector towards to high pressure supply pump.

:21 N·m

• Make sure disk rubber (1) is touching with bolt head of high pressure supply pump (2).
8. Refit in the reverse order to removal for the other refitting

8. Refit in the reverse order to removal for the other refitting operations.

9. Test the sealing of the high pressure after it has been repaired (refer to “SPECIAL FEATURES” in EM- 263, "Precaution for Diesel Equipment").