Engine Mechanical K9K

Timing belt

In this manual: Engine Mechanical K9K
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~6min read
010203040502720N·mlb·ft
Tightening torque found on this page

Exploded View

1. Timing belt inner cover

1. Timing belt inner cover 2. Timing belt
3. Camshaft sprocket
4. Timing belt tensioner 5. Timing belt upper cover 6. Timing belt lower cover 7. Cylinder head suspended bracket 8. Crankshaft pulley
9. Crankshaft sprocket
10. Rear oil seal
11. Rear oil seal retainer 12. Gasket

A Refer to EM-311
B Refer to EM-302

: Always replace after every: N·m (kg-m, ft-lb)
disassembly.: Always replace after every
disassembly.

Removal and Installation: Should be lubricated with oil.


Removal and Installation

CAUTION:
• Apply new engine oil to parts marked in illustration before installation. • Replace any belt that has been removed. • Never turn the engine in the direction opposite to that of normal operation. • When replacing the timing belt, be sure to replace the timing belt tensioner.

• Never run the engine without the drive belts to avoid damaging the crankshaft pulley.

REMOVAL

1. Disconnect battery cable from the negative terminal. 2. Remove engine under cover. 3. Remove front wheel RH. 4. Remove fender protector RH. Refer to EXT-22, "Exploded View" 5. Remove drive belt, and auto-tensioner. Refer to EM-276, "Removal and Installation". 6. Remove RH engine torque rod.

7. Remove RH engine mounting.

8. Remove RH engine mounting support bracket and RH engine mounting

8. Remove RH engine mounting support bracket and RH engine mounting insulator.

9. Remove upper timing cover, camshaft position sensor and cylinder head suspended mounting bracket.

10. Remove timing belt lower cover.10. Remove timing belt lower cover.

10. Remove timing belt lower cover.10. Remove timing belt lower cover.

11. Remove the TDC pin bolt.

11. Remove the TDC pin bolt.

12. Rotate the crankshaft clockwise, until the position (A) of the

12. Rotate the crankshaft clockwise, until the position (A) of the camshaft pulley becomes opposite of the position (B) on the cylinder head.

13. Insert TDC set pin [SST: KV113B0110 (Mot. 1430)] (A) into the

13. Insert TDC set pin [SST: KV113B0110 (Mot. 1430)] (A) into the camshaft pulley and cylinder head hole.

14. Screw in the TDC pin (special service tool).

14. Screw in the TDC pin (special service tool).

15. Turn the engine clockwise (timing side) until the crankshaft

15. Turn the engine clockwise (timing side) until the crankshaft reaches the TDC pin (special service tool).

16. The pin [SST: KV113B0110 (Mot. 1430)] (A) must engage in the

16. The pin [SST: KV113B0110 (Mot. 1430)] (A) must engage in the camshaft pulley and cylinder head holes.

17. Insert flat-bladed screwdriver into the place of crankshaft position

17. Insert flat-bladed screwdriver into the place of crankshaft position sensor to block crankshaft and loosen crankshaft pulley bolt (1).

18. Remove crankshaft pulley.

CAUTION:
Never remove fixing bolts. Keep loosened fixing bolts in place to protect removed crankshaft pulley from dropping.

19. Slacken the timing belt by loosening the bolt of tensioner (1), then remove timing belt.

INSTALLATION

INSTALLATION

Install in the reverse order of removal paying attention to the following.

TIMING ADJUSTMENT

CAUTION:
It is essential to degrease the end of the crankshaft, the bore of the crankshaft sprocket and the bearing faces of the drive belt pulley to prevent any slip between the timing and the crankshaft which would risk destroying the engine.

1. Install timing belt tensioner.

NOTE

:
Put the timing belt tensioner spigot (1) in the cylinder head groove.

2. Insert Tool KV113B0110 (Mot. 1430) (A) in the camshaft pulley and cylinder head holes.

3. Check that the mark on the high pressure pump pulley (2) has shifted one tooth to the right of vertical axle.

4. Turn crankshaft to set Tool KV113B0130 (Mot. 1489) (the crankshaft

4. Turn crankshaft to set Tool KV113B0130 (Mot. 1489) (the crankshaft groove (1) must be facing upwards).

5. Tighten old crankshaft pulley bolt with a spacer (1) (which does

5. Tighten old crankshaft pulley bolt with a spacer (1) (which does not cover the timing sprocket mark).

6. Insert tool KV113B0130 (Mot. 1489) to crankshaft.

6. Insert tool KV113B0130 (Mot. 1489) to crankshaft.

7. Remove one wheel bolt from crankshaft pulley, and then loosen

7. Remove one wheel bolt from crankshaft pulley, and then loosen the other two bolts (1).

8. Install the timing belt, aligning the marks on the belt with those on the

8. Install the timing belt, aligning the marks on the belt with those on the camshaft and fuel injection pump sprockets (19 teeth spaces on the belt between the marks on the camshaft and pump sprockets).

9. Using a 6 mm (0.24 in) Allen key, move the movable index (F) of the tension wheel into the position shown below, by turning the key counterclockwise.

10. Tighten the tension wheel bolt.

10. Tighten the tension wheel bolt.

11. Check that the camshaft pulley wheel bolts are not fully up against the: 27 N·m


11. Check that the camshaft pulley wheel bolts are not fully up against the camshaft pulley wheel.

12. Install and tighten camshaft pulley wheel bolt.

13. Remove Tool KV113B0130 (Mot. 1489) and Tool KV113B0110 (Mot. 1430).: 14 N·m


13. Remove Tool KV113B0130 (Mot. 1489) and Tool KV113B0110 (Mot. 1430). 14. Turn the crankshaft two full turns in a clockwise direction (timing side). Just before the hole (A) of the camshaft pulley is opposite the cylinder head hole (B), insert tool KV113B0130 (Mot. 1489) into the cylinder block.

15. Then turn the crankshaft slowly and smoothly against TDC set pin.

16. Insert TDC set pin [SST: KV113B0110 (Mot. 1430)] (A).

16. Insert TDC set pin [SST: KV113B0110 (Mot. 1430)] (A).

If the pin cannot be inserted, perform the following.

a. Remove TDC set pin [SST: KV113B0130 (Mot. 1489)]. b. Loosen camshaft pulley wheel bolts. c. Turn camshaft pulley to adjust. d. Confirm that the crankshaft sprocket groove is facing upward.

e. Loosen timing belt tensioner bolt.

f. Move the movable index of the drive belt tensioner into the position

f. Move the movable index of the drive belt tensioner into the position as shown in the figure, by turning the key clockwise.

g. Tighten timing belt tensioner bolt.

: 27 N·m

h. Install and tighten camshaft sprocket wheel bolts.

: 14 N·m


i. Turn the crankshaft two revolutions in a clockwise direction (timing

i. Turn the crankshaft two revolutions in a clockwise direction (timing side). Just before the hole (A) of the camshaft pulley is opposite the cylinder head hole (B), insert TDC set pin [SST: KV113B0130 (Mot. 1489)] into the cylinder block.

j. Then turn the crankshaft slowly and smoothly against TDC set pin.

17. Install crankshaft pulley (1), and tighten the bolts as follows:

17. Install crankshaft pulley (1), and tighten the bolts as follows: a. Tighten the bolt.

b. Turn the bolt 95 degrees ±15 degrees clockwise (angle tightening). 120 N·m


b. Turn the bolt 95 degrees ±15 degrees clockwise (angle tightening).

18. Remove TDC set pin [SST: KV113B0130 (Mot. 1489)] and TDC set pin [SST:

18. Remove TDC set pin [SST: KV113B0130 (Mot. 1489)] and TDC set pin [SST: KV113B0110 (Mot. 1430)]. 19. Apply liquid gasket to the thread of TDC pin plug.

20. Install TDC pin plug.

21. Install the cylinder head suspended bracket.: 20 N·m


21. Install the cylinder head suspended bracket.

: 21 N·m


22. Install the lower timing cover by positioning the tab (M) into the

22. Install the lower timing cover by positioning the tab (M) into the hole (N) on the inner timing cover.


23. Install the upper timing cover.

23. Install the upper timing cover.

24. Install the water pipe.

24. Install the water pipe.

25. Install the two water hoses.: 22 N·m


25. Install the two water hoses.

26. Install the alternator bracket.

26. Install the alternator bracket.

: 44 N·m


27. Install the alternator.

27. Install the alternator.

Engine number Tightening torque < D051474 : 21 N·m >≥≥ : 25 N·m

28. Install the A/C compressor.

: 21 N·m


29. Install the power steering pump or the washer which replaces

29. Install the power steering pump or the washer which replaces the pulley (if the engine has one).

: 21 N·m


30. Install the drive belt.

30. Install the drive belt.

CAUTION:
• Make sure belt is correctly engaged with the pulley groove. • Check for oil and coolant on belt and each pulley groove.

• Certain drive belts have five teeth whereas the air conditioning compressor pulley, power-assisted steering pump pulley, and alternator pulley all have six teeth. In this case, it is essential to check that the inner tooth (O) of the pulleys remains free when fitting the drive belt.

Never turn the engine in the opposite direction to its normal operating direction.

Use a brush to remove any deposits from the crankshaft pulley V grooves.

For engines fitted with a mechanical tensioning roller, it is essential to replace the tensioning roller mounting bolts.

31. Make sure that tension of each belt is within the standard.