Brakes

C1111 Abs Motor, Motor Relay System

27steps
~162min
4/5difficulty
Done 0 of 27
DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen item

(Trouble diagnosis content)
DTC detected condition
C1111

PUMP MOTOR

(Pump motor and motor relay)
Diagnosis condition When ignition switch ON.
Signal (terminal) —
Threshold When a malfunction is detected in motor or motor relay.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Harness or connector

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • Battery

  • Harness or connector

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • Battery

FAIL-SAFE

The following functions are suspended:

  • VDC function

  • TCS function

  • ABS function

  • Brake assist function

  • Hill start assist function

DTC Confirmation Procedure

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF → ON, and wait 30 seconds.

  2. Drive the Nissan Murano vehicle at approx. 50 km/h or more for approx. 2 minutes.

  3. Stop the vehicle.

  4. Ignition switch OFF.

  5. Start the engine.

  6. Select “Self Diagnostic Result” mode of “ABS”.

Is DTC “C1111” detected?

YES>>

“CRNT” is displayed: Proceed to DTC Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End. (Erase the memory of “Self Diagnostic Result” mode of “ABS”.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK CONNECTOR

  1. Ignition switch OFF.

  2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness or connector, securely lock the connector, and GO TO 2.

PERFORM SELF DIAGNOSTIC RESULT

CONSULT

  1. Ignition switch OFF → ON, and wait 30 seconds.

  2. Start the engine.

  3. Drive the Nissan Murano vehicle at approx. 50 km/h or more for approx. 2 minutes.

  4. Stop the Nissan Murano vehicle.

  5. Ignition switch OFF.

  6. Start the engine.

  7. Select “Self Diagnostic Result” mode of “ABS”.

Is DTC “C1111” detected?

YES>>

GO TO 3.

NO>>

Inspection End.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or fuse, and GO TO 4.

ERASE SELF DIAGNOSTIC RESULT (1)

CONSULT

  1. Start the engine.

  2. Drive the Nissan Murano vehicle at approx. 50 km/h or more for approx. 2 minutes.

  3. Stop the Nissan Murano vehicle.

  4. Erase the memory of “Self Diagnostic Result” mode of “ABS”.

  5. Ignition switch OFF → ON → OFF.

>>

Inspection End.

CHECK TERMINAL

  1. Ignition switch OFF.

  2. Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Repair / replace harness or connector, and GO TO 6.

ERASE SELF DIAGNOSTIC RESULT (2)

CONSULT

  1. Start the engine.

  2. Drive the Nissan Murano vehicle at approx. 50 km/h or more for approx. 2 minutes.

  3. Stop the Nissan Murano vehicle.

  4. Erase the memory of “Self Diagnostic Result” mode of “ABS”.

  5. Ignition switch OFF → ON → OFF.

>>

Inspection End.