Brakes

C1115 Wheel Sensor

84steps
~504min
5/5difficulty
Done 0 of 84
DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen item

(Trouble diagnosis content)
DTC detected condition
C1115

ABS SENSOR [ABNORMAL SIGNAL]

(Wheel sensor [abnormal signal])
Diagnosis condition
  • When ignition switch ON.

  • When power supply voltage is normal.

Signal (terminal) Wheel sensor circuit power supply
Threshold
  • When difference in wheel speed between any wheel and others is detected the Nissan Murano vehicle is driven, because of installation of other tires than specified.

  • Wheel speed sensorSupply short and battery

Diagnosis delay time 3.5 second or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Harness or connector

  • Wheel sensor

  • Sensor rotor

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • Battery

  • Harness or connector

  • Wheel sensor

  • Sensor rotor

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • Battery

  • Tire size

FAIL-SAFE

The following functions are suspended:

  • VDC function

  • TCS function

  • ABS function

  • EBD function

  • Brake assist function

  • Hill start assist function

DTC Confirmation Procedure

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Start the engine.

  2. Drive the Nissan Murano vehicle at approx. 50 km/h or more for approx. 2 minutes.

  3. Stop the vehicle.

  4. Ignition switch OFF.

  5. Start the engine.

  6. Select “Self Diagnostic Result” mode of “ABS”.

Is DTC “C1115” detected?

YES>>

“CRNT” is displayed: Proceed to DTC Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End. (Erase the memory of “Self Diagnostic Result” mode of “ABS”.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK TIRE

Check the tire air pressure, wear and size. Refer to Tire Air Pressure.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Adjust air pressure or replace tire and GO TO 2.

CHECK DATA MONITOR (1)

CONSULT

  1. Erase the memory of “Self Diagnostic Result” mode of “ABS”.

  2. Ignition switch OFF → ON → OFF.

  3. Start the engine.

  4. Select “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and “RR RH SENSOR” in “Data Monitor” mode of “ABS”.

  5. Read a value (wheel speed) of both normal wheel sensors and error-detecting wheel sensor.

YES>>

GO TO 3.

NO>>

GO TO 4.

PERFORM SELF DIAGNOSTIC RESULT (1)

CONSULT

  1. Stop the Nissan Murano vehicle.

  2. Ignition switch OFF.

  3. Start the engine.

  4. Select “Self Diagnostic Result” mode of “ABS”.

Is DTC “C1115” detected?

YES>>

GO TO 4.

NO>>

Inspection End.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, fuse, or fusible link.

CHECK WHEEL SENSOR AND SENSOR ROTOR

  1. Ignition switch OFF.

  2. Disconnect wheel sensor harness connector.

  3. Remove dust and foreign matter adhered to the wheel sensor and sensor rotor with a vacuum dust collector through the wheel sensor mounting hole.

    • Front: Refer to Exploded View.

    • Rear: Refer to Exploded View.

>>

GO TO 6.

CHECK WHEEL SENSOR

Check the wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 8.

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect ABS actuator and electric unit (control unit) harness connector.

  2. Connect ABS active wheel sensor tester (SST: J-45741) to wheel sensor using appropriate adapter.

  3. Turn the ABS active wheel sensor tester power switch ON.

  4. Spin the wheel of the Nissan Murano vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

GO TO 11.

NO>>

GO TO 8.

REPLACE WHEEL SENSOR (1)

CONSULT

  1. Replace the wheel sensor.

    • Front: Refer to Removal and Installation.

    • Rear: Refer to Removal and Installation.

  2. Connect ABS actuator and electric unit (control unit) harness connector.

  3. Erase the memory of “Self Diagnostic Result” mode of “ABS”

  4. Ignition switch OFF → ON → OFF.

  5. Start the engine.

  6. Select “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and “RR RH SENSOR” in “Data Monitor” mode of “ABS”.

  7. Read the values (wheel speed) of both the normal wheel sensors and malfunctioning wheel sensor.

YES>>

GO TO 9.

NO>>

GO TO 19.

PERFORM SELF DIAGNOSTIC RESULT (2)

CONSULT

  1. Stop the Nissan Murano vehicle.

  2. Ignition switch OFF.

  3. Start the engine.

  4. Select “Self Diagnostic Result” mode of “ABS”.

Is DTC “C1115” detected?

YES>>

GO TO 10.

NO>>

Inspection End.

CHECK CONNECTOR

  1. Ignition switch OFF.

  2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.

  3. Check the wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector, securely lock the connector, and GO TO 11.

CHECK DATA MONITOR (2)

CONSULT

  1. Erase the memory of “Self Diagnostic Result” mode of “ABS”

  2. Ignition switch OFF → ON → OFF.

  3. Start the engine.

  4. Select “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and “RR RH SENSOR” in “Data Monitor” mode of “ABS”.

  5. Read the values (wheel speed) of both the normal wheel sensors and malfunctioning wheel sensor.

YES>>

GO TO 12.

NO>>

GO TO 13.

PERFORM SELF DIAGNOSTIC RESULT (3)

CONSULT

  1. Stop the Nissan Murano vehicle.

  2. Ignition switch OFF.

  3. Start the engine.

  4. Select “Self Diagnostic Result” mode of “ABS”.

Is DTC “C1115” detected?

YES>>

GO TO 13.

NO>>

Inspection End.

CHECK TERMINAL

  1. Ignition switch OFF.

  2. Disconnect ABS actuator and electric unit (control unit) harness connector and then check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with harness connector.

  3. Disconnect wheel sensor harness connector and check each wheel sensor pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 16.

NO>>

Repair / replace harness, connector, or terminal, and GO TO 14.

CHECK DATA MONITOR (3)

CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Connect wheel sensor harness connector.

  3. Erase the memory of “Self Diagnostic Result” mode of “ABS”

  4. Ignition switch OFF → ON → OFF.

  5. Start the engine.

  6. Select “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and “RR RH SENSOR” in “Data Monitor” mode of “ABS”.

  7. Read the values (wheel speed) of both the normal wheel sensors and malfunctioning wheel sensor.

YES>>

GO TO 15.

NO>>

GO TO 16.

PERFORM SELF DIAGNOSTIC RESULT (4)

CONSULT

  1. Stop the Nissan Murano vehicle.

  2. Ignition switch OFF.

  3. Start the engine.

  4. Select “Self Diagnostic Result” mode of “ABS”.

Is DTC “C1115” detected?

YES>>

GO TO 16.

NO>>

Inspection End.

CHECK WHEEL SENSOR HARNESS

  1. Ignition switch OFF.

  2. Disconnect ABS actuator and electric unit (control unit) harness connector.

  3. Disconnect wheel sensor harness connector.

  4. Check the continuity between ABS actuator and electric unit (control unit) harness connector and wheel sensor harness connector. (Check the continuity while turning steering wheel left and right, or while moving center harness in wheel housing.)

    Power Supply Circuit
    ABS actuator and electric unit (control unit)Wheel sensorContinuity
    ConnectorTerminalConnectorTerminal
    E125 19 E18 (Front LH wheel) 1 Yes
    16 E43 (Front RH wheel)
    31 C10 (Rear LH wheel)
    17 C11 (Rear RH wheel)
    Signal Circuit
    ABS actuator and electric unit (control unit)Wheel sensorContinuity
    ConnectorTerminalConnectorTerminal
    E125 8 E18 (Front LH wheel) 2 Yes
    4 E43 (Front RH wheel)
    18 C10 (Rear LH wheel)
    29 C11 (Rear RH wheel)
  5. Check the continuity between ABS actuator and electric unit (control unit) harness connector and the ground.

    Power Supply Circuit
    ABS actuator and electric unit (control unit)—Continuity
    ConnectorTerminal
    E125 16 Ground No
    19
    31
    17

Is the inspection result normal?

YES>>

GO TO 17.

NO>>

Repair / replace harness or connector, and GO TO 17.

CHECK DATA MONITOR (4)

CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Connect wheel sensor harness connector.

  3. Erase the memory of “Self Diagnostic Result” mode of “ABS”

  4. Ignition switch OFF → ON → OFF.

  5. Start the engine.

  6. Select “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and “RR RH SENSOR” in “Data Monitor” mode of “ABS”.

  7. Read the values (wheel speed) of both the normal wheel sensors and malfunctioning wheel sensor.

YES>>

GO TO 18.

NO>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

PERFORM SELF DIAGNOSTIC RESULT (5)

CONSULT

  1. Stop the Nissan Murano vehicle.

  2. Ignition switch OFF.

  3. Start the engine.

  4. Select “Self Diagnostic Result” mode of “ABS”.

Is DTC “C1115” detected?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Inspection End.

REPLACE SENSOR ROTOR

CONSULT

  1. Replace the sensor rotor.

    • Front: Refer to Removal and Installation - Front Sensor Rotor.

    • Rear: Refer to Removal and Installation - Rear Sensor Rotor.

  2. Erase the memory of “Self Diagnostic Result” mode of “ABS”

  3. Ignition switch OFF → ON → OFF.

  4. Start the engine.

  5. Drive the Nissan Murano vehicle at approx. 50 km/h or more for approx. 2 minutes.

  6. Stop the Nissan Murano vehicle.

  7. Ignition switch OFF.

  8. Start the engine.

  9. Select “Self Diagnostic Result” mode of “ABS”.

Is DTC “C1115” detected?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Inspection End.