Brakes

C1197 Vacuum Sensor

24steps
~144min
5/5difficulty
Done 0 of 24
DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen item

(Trouble diagnosis content)
DTC detected condition
C1197

VACUUM SENSOR

(Vacuum sensor)
Diagnosis condition When ignition switch ON.
Signal (terminal) Vacuum sensor malfunction signal
Threshold When a malfunction is detected in vacuum sensor.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Harness or connector

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • Battery

  • Harness or connector

  • Vacuum sensor (brake booster)

  • Vacuum piping

  • ABS actuator and electric unit (control unit)

FAIL-SAFE

Electrical vacuum assistance of brake booster is suspended.

DTC Confirmation Procedure

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF.

  2. Start the engine.

  3. Perform “Self Diagnostic Result” mode of “ABS”.

Is DTC “C1197” detected?

YES>>

“CRNT” is displayed: Proceed to DTC Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of “Self Diagnostic Result” mode of “ABS”.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK CONNECTOR

  1. Ignition switch OFF.

  2. Check the vacuum sensor harness connector for disconnection or looseness.

  3. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair / replace harness or connector, and GO TO 2.

CHECK BRAKE BOOSTER

  1. Ignition switch OFF.

  2. Check the brake booster. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace the brake booster. Refer to Removal and Installation.

CHECK VACUUM PIPING

Check the vacuum piping. Refer to Exploded View.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace the vacuum piping. Refer to Removal and Installation.

CHECK TERMINAL

  1. Ignition switch OFF.

  2. Disconnect vacuum sensor harness connector.

  3. Check the vacuum sensor pin terminals for damage or loose connection with harness connector.

  4. Disconnect ABS actuator and electric unit (control unit) harness connector.

  5. Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal.

CHECK VACUUM SENSOR CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect vacuum sensor harness connector.

  3. Disconnect ABS actuator and electric unit (control unit) harness connector.

  4. Check the continuity between vacuum sensor harness connector and ABS actuator and electric unit (control unit) harness connector.

    Vacuum sensorABS actuator and electric unit (control unit)Continuity
    ConnectorTerminalConnectorTerminal
    E167 1 E125 12 Yes
    2 24
    3 5
  5. Check the continuity between vacuum sensor harness connector and ground.

    Vacuum sensor—Continuity
    ConnectorTerminal
    E167 1 Ground No
    2
    3

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness or connector.

REPLACE VACUUM SENSOR

CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Replace the vacuum sensor.

  3. Erase the memory of “Self Diagnostic Result” mode of “ABS”.

  4. Ignition switch OFF → ON → OFF.

  5. Start engine.

  6. Select “Self Diagnostic Result” mode of “ABS”.

Is DTC “C1197” detected?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Inspection End.