Speaker Circuit
DESCRIPTION
If there is a short circuit in a speaker, the radio receiver assembly detects it and stops outputting to the speakers.
As a result, no sound is heard from the speakers, even if there is no malfunction in the radio receiver assembly or the speakers.
WIRING DIAGRAM
PROCEDURE
CHECK WIRE HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - SPEAKERS)
(a) Disconnect connectors F48 and F49 from the radio receiver assembly.
(b) Disconnect the I1 and J1 connectors from the Front Speaker Assembly No. 1.
(c) Disconnect the F85 and F86 connectors from the Front Speaker Assembly No. 2.
(d) Disconnect the K4 and L4 rear speaker assembly connectors.
(e) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
F48-1 (FR+) - F85-4 (TWR+) |
Always |
Below 1 Ω |
F48-5 (FR-) - F85-2 (TWR-) |
Always |
Below 1 Ω |
F85-3 (+) - I1-1 |
Always |
Below 1 Ω |
F85-1 (-) - I1-2 |
Always |
Below 1 Ω |
F48-2 (FL+) - F86-4 (TWL+) |
Always |
Below 1 Ω |
F48-6 (FL-) - F86-2 (TWL-) |
Always |
Below 1 Ω |
F86-3 (+) - J1-1 |
Always |
Below 1 Ω |
F86-1 (-) - J1-2 |
Always |
Below 1 Ω |
F49-1 (RR+) - K4-1 |
Always |
Below 1 Ω |
F49-3 (RR-) - K4-2 |
Always |
Below 1 Ω |
F49-2 (RL+) - L4-1 |
Always |
Below 1 Ω |
F49-6 (RL-) - L4-2 |
Always |
Below 1 Ω |
F48-1 (FR+) or F85-4 (TWR+) - Body ground |
Always |
10 kΩ minimum |
F48-5 (FR-) or F85-2 (TWR-) - Body ground |
Always |
10 kΩ minimum |
F85-3 (+) or I1-1 - Body ground |
Always |
10 kΩ minimum |
F85-1 (-) or I1-2 - Body ground |
Always |
10 kΩ minimum |
F48-2 (FL+) or F86-4 (TWL+) - Body ground |
Always |
10 kΩ minimum |
F48-6 (FL-) or F86-2 (TWL-) - Body ground |
Always |
10 kΩ minimum |
F86-3 (+) or J1-1 - Body ground |
Always |
10 kΩ minimum |
F86-1 (-) or J1-2 - Body ground |
Always |
10 kΩ minimum |
F49-1 (RR+) or K4-1 - Body ground |
Always |
10 kΩ minimum |
F49-3 (RR-) or K4-2 - Body ground |
Always |
10 kΩ minimum |
F49-2 (RL+) or L4-1 - Body ground |
Always |
10 kΩ minimum |
F49-6 (RL-) or L4-2 - Body ground |
Always |
10 kΩ minimum |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT NO. 1 FRONT SPEAKER ASSEMBLY
(a) Remove the No. 1 front speaker assembly.
Click here![]()
(b) Inspect the No. 1 front speaker assembly.
Click here![]()
| NG | REPLACE NO. 1 FRONT SPEAKER ASSEMBLY |
|
INSPECT NO. 2 FRONT SPEAKER ASSEMBLY
(a) Remove the No. 2 front speaker assembly.
Click here![]()
(b) Inspect the No. 2 front speaker assembly.
Click here![]()
| NG | REPLACE NO. 2 FRONT SPEAKER ASSEMBLY |
|
REPLACE NO. 2 FRONT SPEAKER ASSEMBLY
(a) Confirm that the malfunction disappears when a good speaker is installed.
Click here![]()
OK:
The malfunction disappears.
HINT:
- Connect all connectors that were disconnected to the No. 2 front speaker assemblies.
- If the No. 2 front right or left speaker assembly appears to be defective, check by swapping the two speakers.
- Perform the check described above for both the right and left sides.
| OK | END (NO. 2 FRONT SPEAKER ASSEMBLY WAS DEFECTIVE) |
|
INSPECT REAR SPEAKER ASSEMBLY
(a) Remove the rear speaker assembly.
Click here![]()
(b) Inspect the rear speaker assembly.
Click here![]()
| OK | GO TO APPLICABLE SYSTEM AS INDICATED IN THE PROBLEM SYMPTOMS TABLE |
| NG | REPLACE REAR SPEAKER ASSEMBLY |