Audio / Video

System Description

~15min read

SYSTEM DESCRIPTION

CD (Compact Disc) Player Description

(a) A CD player uses a laser pickup to read the digital signals recorded on a compact disc (CD). By converting the digital signals into analogue signals, it is able to play music and audio media.

CAUTION:

Do not look directly at the laser pickup as the CD player uses an invisible laser beam. Make sure to use the player as instructed.

NOTICE:

  • Do not disassemble any part of the CD player.
  • Do not apply grease or oil to the CD player.
  • Insert only CDs into the CD player.

(b) Playable discs

(1) This player can only play audio CDs, CD-Rs (recordable CDs) and CD-RWs (rewritable CDs) bearing one of the following symbols:

(c) Precautions when using discs

NOTICE:

  • Copy-protected CDs cannot be played.
  • CD-Rs and CD-RWs may not play due to their recording conditions or characteristics, or simply because they have been left in the vehicle for a long time and have been damaged, dirty or deteriorated.
  • CD-Rs and CD-RWs that have not been finalised cannot be played.
  • Double-sided discs consisting of a DVD recorded on one side and a digital audio CD on the other cannot be played.
  • Keep discs free from dirt. Take care not to damage the discs or leave fingerprints on them.
  • Hold discs by the outer edge and the centre hole with the label facing up.
  • Leaving a disc partially ejected from its slot for a long time may cause it to warp and become unusable.
  • Adhesive tape, stickers, disc labels or any adhesive residue may prevent the disc from being ejected or cause the player to malfunction.
  • Keep discs out of direct sunlight (exposure to direct sunlight may cause the disc to warp and become unusable).
  • Do not use specially shaped discs as they may cause the player to malfunction.
  • Do not use discs whose recording surface is transparent or translucent as they may not be inserted, ejected or played normally.
  • Use only 4.7 in (12 cm) discs.
  • Do not use 3 in (8 cm) discs, with or without adaptors.

HINT:

  • In rainy or cold weather, fogging on the windows may indicate fogging and condensation inside the player. In this case, the disc may skip or stop partway through playback. Ventilate or dehumidify the cabin for some time before using the player.
  • The disc may skip if the vehicle is subjected to strong vibrations, for example when driving on a rough or uneven road surface.

(d) Cleaning

NOTICE:

Do not use lens cleaning products as they may cause the player's pickup to malfunction.

(1) If the disc surface is dirty, wipe it with a soft, dry cloth, such as a plastic lens or eyeglass cleaning cloth, from the centre towards the outer edge.

NOTICE:

  • Pressing the disc with your hand or rubbing it with a rough cloth may scratch the disc surface.
  • Using solvents such as disc sprays, antistatic agents, alcohol, petrol, thinners or a cloth impregnated with cleaning solution may damage the disc and make it unusable.

MP3/WMA GENERAL DESCRIPTION

(a) Playable MP3 file standards

Compatible standard

MP3 (MPEG1 LAYER3, MPEG2 LSF LAYER3)

Compatible sampling rate

  • MPEG1 LAYER3: 32, 44.1, 48 (kHz)
  • MPEG2 LSF LAYER3: 16, 22.05, 24 (kHz)

Compatible bit rate

  • MPEG1 LAYER3: 32, 40, 48, 56, 64, 80, 96, 112, 128, 160, 192, 224, 256, 320 (kbps)
  • MPEG2 LSF LAYER3: 8, 16, 24, 32, 40, 48, 56, 64, 80, 96, 112, 128, 144, 160 (kbps)
  • VBR compatible

Compatible channel mode

Stereo, joint stereo, dual channel, mono

(b) Playable WMA file standards

Compatible standard

WMA version 7, 8 and 9

Compatible sampling rate

32, 44.1, 48 (kHz)

Compatible bit rate (compatible with dual channel playback only)

  • Version 7, 8: CBR48, 64, 80, 96, 128, 160, 192 (kbps)
  • Version 9: CBR48, 64, 80, 96, 128, 160, 192, 256, 320 (kbps)

(c) ID3 tag and WMA tag reference

(1) Additional text information, called ID3 tags, can be entered into MP3 files. Information such as song titles and artist names can be stored.

HINT:

This player is compatible with ID3 tags of versions ID3 1.0 and 1.1, and ID3 Ver. 2.2 and 2.3 (number of characters conforming to ID3 versions 1.0 and 1.1).

(2) Additional text information, called WMA tags, can be entered into WMA files. Information such as song titles and artist names can be stored.

(d) Playable media

(1) Only CD-ROMs, CD-Rs (recordable CDs) and CD-RWs (rewritable CDs) can be used to play MP3/WMA files.

NOTICE:

  • CD-Rs and CD-RWs are more sensitive to hot and humid environments than standard audio CDs. For this reason, some CD-Rs and CD-RWs may not play.
  • The disc may not play or may skip if it has fingerprints or scratches.
  • Some CD-Rs and CD-RWs deteriorate if left in the vehicle for too long.
  • Store CD-Rs and CD-RWs in an opaque case.

(e) Playable media format

(1) Playable media format

Disc format

CD-ROM Mode 1, CD-ROM XA Mode 2 Form 1 and Form 2

File format

ISO9660 Level 1 and Level 2 (Joliet, Romeo)

HINT:

  • MP3/WMA files written in an unsupported format may not play normally, or file or folder names may not display correctly.
  • This player is compatible with multi-session discs and can play CD-Rs and CD-RWs to which MP3/WMA files have been added. However, only the first session can be played.
  • Discs whose first session contains both music data and MP3 or WMA data cannot be played.

(2) Standards and restrictions

Maximum folder levels

8 levels

Maximum number of characters for a folder/file name

32 characters

Maximum number of folders

192 (including empty folders, playlist folders and folders that do not contain MP3/WMA files)

Maximum number of files on a disc

255 (including non-MP3/WMA files)

(f) File names

(1) Only files with a ".mp3" or ".wma" extension can be recognised and played as MP3 or WMA files.

(2) Saving MP3 or WMA files with a ".mp3" or ".wma" extension.

NOTICE:

If non-MP3 or non-WMA files are saved with a ".mp3" or ".wma" extension, these files may still be recognised as MP3 or WMA files and played. However, loud noise may be produced and the speaker may be damaged.

GENERAL DESCRIPTION OF "Bluetooth" TECHNOLOGY

*1

Radio receiver assembly

(built-in "Bluetooth" receiving antenna)

-

-

*a

Example

*b

Mobile network

*c

Mobile phone

(Bluetooth compatible)

*d

Bluetooth compatible

(Bluetooth compatible)

*e

Bluetooth wireless connection

-

-

(a) "Bluetooth" is a registered trademark owned by Bluetooth SIG, Inc.

(b) "Bluetooth" is a wireless connection technology that uses the 2.4 GHz frequency band.

HINT:

Communication performance of "Bluetooth" technology varies depending on obstacles or conditions in which radio waves travel between communication devices, electromagnetic waves, the sensitivity of the communication devices, or the capacity of the antenna.

(c) Hands-free function

(1) The integrated "Bluetooth" radio receiver unit and a "Bluetooth"-compatible mobile phone* can be connected using a "Bluetooth" wireless connection. This feature allows the hands-free function of the mobile phone to be used even if the phone is in a pocket or bag. Therefore, it is not necessary to use a connector or cable to connect the mobile phone.

*: Some versions of "Bluetooth" compatible mobile phones may not operate correctly.

(2) The hands-free function uses a "Bluetooth" wireless connection. A "Bluetooth" wireless connection can be affected by factors with uncertain effects, such as the vehicle location, time of day, etc. Therefore, connection problems may temporarily be caused by "Bluetooth" connection conditions. When performing diagnostic procedures, it is necessary to check the transmission frequency, the connection status using another mobile phone, etc.

(3) Compatible hands-free devices

Required "Bluetooth" specifications

Ver. 1.1 or later (ver. 2.1+EDR recommended)

Supported profiles

  • HFP (Hands-Free Profile) ver. 1.0 or later (ver. 1.5 minimum recommended)*
  • OPP (Object Push Profile) Ver. 1.1
  • PBAP (Phone Book Access Profile) Ver. 1.0

Maximum number of hands-free devices that can be registered (including audio devices)

5

  • *: This profile is required when using the hands-free function.

(d) "Bluetooth" audio function

(1) The integrated "Bluetooth" radio receiver unit and a "Bluetooth"-compatible portable audio player* can be connected using a "Bluetooth" wireless connection. Files stored on the portable audio player can then be played through the vehicle speakers. In addition, functions such as play/stop can be operated directly from the radio receiver unit.

*: Some versions of "Bluetooth"-compatible portable audio players may not connect via "Bluetooth", or music may play but the functions accessible from the radio receiver unit may be limited.

(2) "Bluetooth"-compatible audio devices

Required "Bluetooth" specifications

Ver. 1.1 or later (ver. 2.1+EDR recommended)

Supported profiles

  • A2DP (Advanced Audio Distribution Profile) ver. 1.0 or later (ver. 1.2 or later recommended)
  • AVRCP (Audio/Video Remote Control Profile) ver. 1.0 or later (ver. 1.3 or later recommended)

Maximum number of audio devices that can be registered (including hands-free devices)

5

RADIO DESCRIPTION

(a) Radio frequency band

(1) Radio broadcasts use the frequency bands shown in the table below.

(b) Reception area

(1) The reception areas for AM and FM broadcasts differ greatly. Sometimes an AM broadcast can be received much more clearly than a stereo FM broadcast. Stereo FM has the smallest reception area and tends to pick up static and other interference such as noise.

*a

FM (stereo)

*b

FM (mono)

*c

AM

(c) Radio reception problems

HINT:

In addition to static interference, other problems exist such as "phasing", "multipath interference" and "signal fading". These problems are not caused by electrical noise but by the very method of radio signal propagation.

(1) Phasing

AM broadcasts are subject to electrical interference and to another type of interference called "phasing". Occurring only at night, phasing is interference created when a vehicle receives 2 radio wave signals from the same transmitter. One of the signals is reflected by the ionosphere and the other is received directly from the transmitter.

*a

Phasing

*b

Ionosphere

(2) Multipath interference

Multipath interference occurs when a vehicle receives 2 radio wave signals from the same transmitter. One of the signals is reflected by buildings or mountains and the other is received directly from the transmitter.

*a

Multipath interference

(3) Signal fading

Signal loss is caused by obstacles (buildings, mountains or similar obstructions) that deflect part of the signal; this results in weaker signal reception when the obstacle is between the transmitter and the vehicle. High-frequency radio waves, such as FM broadcasts, are easily deflected by obstacles. Low-frequency radio waves, such as AM broadcasts, are less likely to be deflected.

*a

Signal fading

(d) Noise problems

Technicians must pay particular attention to noise problems reported by the customer. Use the following table to diagnose noise problems.

Radio frequency

Noise occurrence condition

Probable cause

AM

Noise occurs at certain locations

External noise

Noise occurs when listening to an intermittent broadcast

The same program broadcast from several transmitters may cause noise when the signals interfere with each other

Noise occurs only at night

Signal phasing

FM

Noise occurs at certain locations while driving

Multipath interference resulting from an FM frequency change

USB AUDIO SYSTEM FUNCTION DESCRIPTION

(a) The audio unit is equipped with a USB port. Connecting a USB device or "iPod" to the audio unit allows music files to be played. Not only can music be played from a USB device equipped with audio functions, but MP3 or WMA files stored on a USB device can also be played. In addition, the "iPod" software is installed, allowing files to be selected from playlists and the shuffle mode to be used.

HINT:

Operations using the controls of a connected USB device or "iPod" cannot be performed while it is connected.

(b) The audio unit is equipped with a USB port. Connecting a USB device or "iPod" to the audio unit allows music files to be played. Not only can music be played from a USB device equipped with audio functions, but MP3 or WMA files stored on a USB device can also be played. In addition, the "iPod" software is installed, allowing files to be selected from playlists and the shuffle mode to be used.

HINT:

Operations using the controls of a connected USB device or "iPod" cannot be performed while it is connected.

(c) Devices compatible with USB audio systems

(1) USB Device

The following device formats can be used:

Compatible USB Device Formats

  • USB communication format: USB 2.0 FS (12 Mbps)
  • File System: FAT16/32 (Windows)
  • Class: Mass Storage Class

MP3 and WMA files recorded on a USB device in a format other than those listed above may not play correctly. Their names and folder names may not display correctly.

The standards and limitations are as follows:

  • Maximum directory tree depth: 8 levels
  • Maximum number of folders on the device: 999 (including the root folder)
  • Maximum number of files on the device: 9999
  • Maximum number of files per folder: 255

(2) "iPod"

"iPhone", "iPod", "iPod classic", "iPod nano" and "iPod touch" are trademarks of Apple Inc., registered in the U.S. and other countries.

"iPod", "iPod nano", "iPod classic", "iPod touch" and "iPhone" devices can be used with this system.

Compatible with:

  • "iPod touch" (4th generation)
  • "iPod touch" (3rd generation)
  • "iPod touch" (2nd generation)
  • "iPod touch" (1st generation)
  • "iPod classic"
  • "iPod with video"
  • "iPod nano" (6th generation)
  • "iPod nano" (5th generation)
  • "iPod nano" (4th generation)
  • "iPod nano" (3rd generation)
  • "iPod nano" (2nd generation)
  • "iPod nano" (1st generation)
  • "iPhone 4S"
  • "iPhone 4"
  • "iPhone 3GS"
  • "iPhone 3G"
  • "iPhone"

HINT:

Depending on differences between models or software versions, some models may not be compatible with this system.

DESCRIPTION OF ASL (AUTOMATIC SOUND LEVELIZER) FUNCTION

(a) The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume level to compensate for increasing vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL function adjusts the volume level based on the vehicle speed signals it receives from the instrument cluster assembly.