Removal
REMOVAL
PRECAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during cooler condenser removal/installation are shown below.
Procedure Required After Replacing / Removing / Installing PartsReplacement part or procedure | Necessary Procedures | Effects / Inoperative Function When Necessary Procedure Not Performed | Link |
|---|---|---|---|
Disconnect the cable from the negative (-) battery terminal. |
Memorize Steering Angle Neutral Point |
Lane Departure Alert System (with Steering Control) |
|
Pre-Collision System |
|||
Initialize Back Door Lock |
Door Lock Control System |
PROCEDURE
1. RECOVER REFRIGERANT FROM REFRIGERANT SYSTEM (for HFC-134a (R134a))
Click here![]()
2. RECOVER REFRIGERANT FROM REFRIGERANT SYSTEM (for HFO-1234yf (R1234yf))
Click here![]()
3. REMOVE HEADLIGHT ASSEMBLY LH (for Halogen Headlight)
Click here![]()
4. REMOVE HEADLIGHT ASSEMBLY LH (for LED Headlight)
Click here![]()
5. REMOVE HEADLIGHT ASSEMBLY RH (for Halogen Headlight)
HINT:
Perform the same procedure as for the left side.
6. REMOVE HEADLIGHT ASSEMBLY RH (for Light Emitting Diode Headlight)
HINT:
Perform the same procedure as for the left side.
7. REMOVE AIR CLEANER INLET NO. 1
Click here![]()
8. REMOVE FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY
Click here![]()
9. REMOVE RADIATOR GRILLE RETAINER NO. 1
Click here![]()
10. REMOVE RADIATOR SUPPORT SEAL NO. 1
Click here![]()
11. REMOVE HOOD LOCK NUT CAP
Click here![]()
12. REMOVE HOOD LOCK ASSEMBLY
- with engine room courtesy light switch:
Click here
.gif)
- without engine room courtesy light switch:
Click here
.gif)
13. REMOVE RADIATOR SUPPORT UPPER SUB-ASSEMBLY
Click here![]()
14. REMOVE RADIATOR AIR GUIDE NO. 2
Click here![]()
15. REMOVE FRONT BUMPER ENERGY ABSORBER
Click here![]()
16. REMOVE FRONT BUMPER REINFORCEMENT
Click here![]()
17. REMOVE RADIATOR AIR GUIDE LH NO. 1
Click here![]()
18. REMOVE RADIATOR AIR GUIDE RH NO. 1
Click here![]()
19. DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY
(a) Remove the bolt to disconnect the discharge hose sub-assembly from the cooler condenser assembly. |
![]() |
(b) Remove the O-ring from the discharge hose sub-assembly.
NOTICE:
Using vinyl tape, seal the openings of the disconnected parts to prevent moisture or foreign matter from entering.
20. DISCONNECT COOLER LIQUID TUBE A (VALEO make)
(a) Remove the bolt to disconnect the cooler liquid tube A from the cooler condenser assembly. |
![]() |
(b) Remove the O-ring from the cooler liquid tube A.
NOTICE:
Using vinyl tape, seal the openings of the disconnected parts to prevent moisture or foreign matter from entering.
21. DISCONNECT COOLER LIQUID TUBE A (DENSO make)
(a) While pushing the end of the cooler liquid tube A into the end of the cooler condenser assembly, use pliers to squeeze both sides of the tube clamp together until it breaks.
*1 |
Cooler Liquid Tube A |
*2 |
Cooler Condenser Assembly |
*3 |
Pipe Clamp |
- |
- |
*a |
Push in |
- |
- |
NOTICE:
- If foreign objects are stuck to the connector, use a brush or compressed air to remove them.
- Make sure that fragments of the pipe clamp do not enter the pipe.
(b) Disconnect the cooler liquid tube A.
NOTICE:
Remove any foreign matter near the ends of the cooler liquid tube A and the cooler condenser assembly.
(c) Remove the 2 O-rings from the cooler liquid tube A.
NOTICE:
Wrap the open ends of the separated cooler condenser assembly and the cooler liquid tube A accessory assembly with vinyl tape to prevent moisture or foreign matter from entering.
(d) Remove the tube clamp.
22. REMOVE COOLER CONDENSER ASSEMBLY
(a) Release the claws and guides to remove the cooler condenser assembly as shown in the illustration.
![]() |
Remove in this direction (1) |
![]() |
Remove in this direction (2) |
NOTICE:
Take care not to damage the cooler condenser assembly or the radiator assembly when removing the cooler condenser assembly.


.png)
.png)