Heater / Air Conditioning

Installation

~5min read
010203040505.44N·mlb·ft
Tightening torque found on this page

INSTALLATION

PROCEDURE

1. INSTALL COOLER CONDENSER ASSEMBLY

(a) Engage the 2 guides and the 2 claws to install the cooler condenser assembly as shown in the illustration.

Install in this direction (1)

Install in this direction (2)

NOTICE:

Take care not to damage the cooler condenser assembly or the radiator assembly when installing the cooler condenser assembly.

HINT:

If a new cooler condenser assembly is installed, add compressor oil to the cooler condenser assembly as follows.

Quantity:

Add 40 cm3 (1.35 fl.oz.)

Compressor oil:

Manufactured by VALEO

VC100YF or equivalent

Manufactured by DENSO

ND-OIL 12 or equivalent

2. CONNECT COOLER LIQUID TUBE A (VALEO make)

(a) Remove the vinyl tape from the cooler liquid tube A and the cooler condenser assembly.

(b) Apply sufficient compressor oil to a new O-ring and the connecting surfaces of the cooler liquid tube A.

Compressor oil:

VC100YF or equivalent

(c) Install the O-ring to the cooler refrigerant liquid tube A.

NOTICE:

Keep the O-rings and O-ring mating surfaces free of foreign matter.

(d) Connect the cooler liquid tube A to the cooler condenser assembly with the bolt.

Torque:

5.4 N·m {55 kgf·cm, 48 in·lbf}

3. CONNECT COOLER LIQUID TUBE A (DENSO make)

(a) Remove the vinyl tape from the open ends of the cooler condenser assembly and the cooler liquid tube A.

(b) Install a new tube clamp to the cooler liquid tube A.

NOTICE:

  • Firmly engage the inner notch of the tube clamp in the groove of the cooler liquid tube A.
  • Do not widen the opening of the tube clamp by more than the diameter of the cooler liquid tube A when installing.
  • Do not install the pipe clamp with the large-diameter section facing the wrong direction.

*1

Air Conditioning Tube and Accessory Assembly

*2

Pipe Clamp

*a

Groove

(c) Completely coat 2 new O-rings and the contact surface of the cooler liquid tube A with compressor oil.

Compressor oil:

ND-OIL 12 or equivalent

(d) Install the 2 O-rings to the cooler liquid tube A.

NOTICE:

Prevent foreign matter from adhering to the O-rings or the O-ring sealing surfaces.

(e) Engage the cooler condenser assembly and the cooler liquid tube A.

*a

Large-diameter section of pipe clamp

-

-

NOTICE:

Insert the parts while holding the pipe, not the pipe clamp.

(f) Insert the pipe clamp correctly until the large-diameter section of the pipe clamp is covered by the cooler condenser assembly.

HINT:

  • When inserting, make sure a click is heard.
  • Make sure that the cooler liquid refrigerant hose A is correctly inserted by pulling on it.

4. CONNECT DISCHARGE HOSE SUB-ASSEMBLY

(a) Detach the vinyl tape from the discharge hose sub-assembly and the connector piece of the cooler condenser assembly.

(b) Apply sufficient compressor oil to a new O-ring and to the mating surface of the discharge hose sub-assembly.

Compressor oil:

Manufactured by VALEO

VC100YF or equivalent

Manufactured by DENSO

ND-OIL 12 or equivalent

(c) Install the O-ring to the discharge hose sub-assembly.

(d) Connect the discharge hose sub-assembly to the cooler condenser assembly with the bolt.

Torque:

5.4 N·m {55 kgf·cm, 48 in·lbf}

5. INSTALL NO. 1 RADIATOR AIR GUIDE LH

Click here

6. INSTALL NO. 1 RADIATOR AIR GUIDE RH

Click here

7. INSTALL FRONT BUMPER REINFORCEMENT

Click here

8. INSTALL FRONT BUMPER ENERGY ABSORBER

Click here

9. INSTALL NO. 2 RADIATOR AIR GUIDE

Click here

10. INSTALL RADIATOR UPPER SUPPORT SUB-ASSEMBLY

Click here

11. INSTALL HOOD LOCK ASSEMBLY

  • with engine room courtesy light switch:

    Click here

  • without engine room courtesy light switch:

    Click here

12. INSTALL HOOD LOCK NUT CAP

Click here

13. INSTALL NO. 1 RADIATOR SUPPORT SEAL

Click here

14. INSTALL NO. 1 RADIATOR GRILLE RETAINER

Click here

15. INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY

Click here

16. INSTALL NO. 1 AIR CLEANER INLET

Click here

17. INSTALL LH HEADLIGHT ASSEMBLY (for Halogen Headlight)

Click here

18. INSTALL LH HEADLIGHT ASSEMBLY (for LED Headlight)

Click here

19. INSTALL RH HEADLIGHT ASSEMBLY (for Halogen Headlight)

HINT:

Perform the same procedure as for the left side.

20. INSTALL RH HEADLIGHT ASSEMBLY (for Light Emitting Diode Headlight)

HINT:

Perform the same procedure as for the left side.

21. CHARGE REFRIGERANT INTO AIR CONDITIONING SYSTEM (for HFC-134a (R134a))

Click here

22. CHARGE REFRIGERANT INTO AIR CONDITIONING SYSTEM (for HFO-1234yf (R1234yf))

Click here

23. WARM UP ENGINE (for HFC-134a (R134a))

Click here

24. WARM UP ENGINE (for HFO-1234yf (R1234yf))

Click here

25. CHECK FOR REFRIGERANT LEAKAGE (for HFC-134a (R134a))

Click here

26. CHECK FOR REFRIGERANT LEAKAGE (for HFO-1234yf (R1234yf))

Click here

27. ADJUST HOOD LOCK ASSEMBLY

Click here