Symptom Table
SYMPTOM TROUBLESHOOTING TABLE
NOTICE:
- The following events may occur if a radio receiver and display assembly from another vehicle is installed in this vehicle. Therefore, when replacing the radio receiver and display assembly, be sure to replace it with a new part.
- A communication malfunction DTC is stored.
- The radio receiver and display assembly does not operate normally.
- If the DCM (telematics transceiver) has been replaced, perform the DCM activation procedure.
Click here
.gif)
HINT:
- Use the table below to determine the cause of the symptoms. If several suspected areas are listed, the possible causes of the symptom are shown in order of probability in the "Suspected Area" column of the table. Check each symptom, verifying the suspected areas in the order listed. Replace parts if necessary.
- Check the fuses and relays associated with this system before checking the suspected areas listed below.
Symptom | Suspected Area | Link |
|---|---|---|
A message is temporarily displayed advising to wait a moment and try again because the lines are busy. |
This is caused by radio wave signal conditions or because the call center is busy. It is not a malfunction. (Inform the customer that there is no malfunction and ask them to use the system as is.) |
- |
Contact the call center |
- |
|
Radio and Display Receiver Assembly |
||
DCM (Telematics Transceiver) |
||
A message is displayed advising to wait a moment and try again because the information cannot be retrieved due to a busy line, etc. |
Wait a moment and perform the operation again in a different location |
- |
Contact the call center |
- |
|
Radio and Display Receiver Assembly |
||
DCM (Telematics Transceiver) |
||
A message is displayed advising to try again because the information could not be retrieved |
Contact the call center |
- |
Radio and Display Receiver Assembly |
||
DCM (Telematics Transceiver) |
||
A message is displayed advising to try again after a moment because communication is being established |
The system is trying to detect the DCM (telematics transceiver). Wait a moment and perform the operation again |
- |
Contact the call center |
- |
|
Radio and Display Receiver Assembly |
||
DCM (Telematics Transceiver) |
||
A message is displayed advising to move the vehicle to a communication workshop because it is outside a workshop |
Wait a moment and restart the operation in another location (in a communication workshop) |
- |
Contact the call center |
- |
|
Radio and Display Receiver Assembly |
||
DCM (Telematics Transceiver) |
||
A message is displayed advising to move the vehicle to a location where a GPS signal can be received because the time data has expired |
Follow the "GPS mark is not displayed" procedure |
|
If the GPS mark is displayed, wait a moment and restart the operation in another location |
- |
|
If the symptom reoccurs, replace the radio receiver and display assembly |
||
A message is displayed indicating that this service is currently unavailable |
Explain to the customer that the service is currently unavailable. |
- |
A message is displayed advising to ask the dealer about the service request, because a contract must be created before using the service |
Confirm the status of the paid service contract. |
- |
Contact the call center |
- |
Symptom | Suspected Area | Link |
|---|---|---|
Cannot call the call center when Call Dest. Assist is selected on the Destination Assist Connect screen |
Contact the telematics service provider to check the network status |
- |
Follow the "UNABLE TO CONNECT TO CALL CENTER" procedure |
||
Follow the "DCM data signal circuit between navigation ECU and DCM" procedure |
||
Radio and Display Receiver Assembly |
||
DCM (Telematics Transceiver) |
||
The volume of the other caller's voice cannot be adjusted using the Destination Assist Connect screen |
Radio and Display Receiver Assembly |
Symptom | Suspected Area | Link |
|---|---|---|
Voice commands performed to contact the assistance center are not recognized |
Check whether the Toyota Entune System is available |
- |
Check whether the voice recognition function operates correctly |
||
Follow the "Voice commands performed to contact the assistance center are not recognized" procedure |
||
The dynamic voice recognition function does not operate |
Check whether the Toyota Entune System is available |
- |
Follow the "UNABLE TO CONNECT TO CALL CENTER" procedure |
Symptom | Suspected Area | Link |
|---|---|---|
The Toyota Entune App Suite Connect error message is displayed on the screen |
Follow the instructions displayed on the screen |
- |
Perform "Confirm Mobile Phone Functionality" |
||
Perform "Confirm Vehicle Radio Functionality" |
||
Follow the "App Suite Connect Function Reset Procedure" when verifying operation |
||
Radio and Display Receiver Assembly |
||
Toyota Entune App Suite Connect and services do not operate as expected |
Perform "Confirm Mobile Phone Functionality" |
|
Perform "Confirm Vehicle Radio Functionality" |
||
Follow the "App Suite Connect Function Reset Procedure" when verifying operation |
||
Radio and Display Receiver Assembly |
||
Voice recognition for the Toyota Entune App Suite Connect function is not possible (voice recognition for the audio and visual system operates normally) |
Perform "Confirm Mobile Phone Functionality" |
|
Perform "Confirm Vehicle Radio Functionality" |
||
Follow the "App Suite Connect Function Reset Procedure" when verifying operation |
||
Radio and Display Receiver Assembly |
||
The sound quality of the Toyota Entune App Suite Connect function is poor |
Check that the mobile phone handset volume is not at minimum |
- |
Confirm that an appropriate signal is maintained while driving the vehicle |
- |
|
Perform "Confirm Mobile Phone Functionality" |
||
Perform "Confirm Vehicle Radio Functionality" |
||
Follow the "App Suite Connect Function Reset Procedure" when verifying operation |
||
Radio and Display Receiver Assembly |