Toyota Tacoma Quiz
Brake Control / Dynamic Control Systems

TRAC OFF Indicator Light does not Come ON

In this manual: Brake Control / Dynamic Control Systems
Introduction — 15Maintenance — 8Audio / Video — 94Garage Door Opener — 7Navigation / Multi Info Display — 84Park Assist / Monitoring — 86Brake — 50Brake Control / Dynamic Control Systems — 165Parking Brake — 52gr-fks Charging — 252gr-fks Cooling — 212gr-fks Emission Control — 132gr-fks Engine Control — 322gr-fks Engine Mechanical — 332gr-fks Exhaust — 92gr-fks Fuel — 422gr-fks Ignition — 62gr-fks Intake — 72gr-fks Lubrication — 152gr-fks Starting — 38Ac60e Automatic Transmission / Transaxle — 146Axle — 19Clutch — 20Cruise Control — 168Differential — 50Drive Shaft — 6Propeller Shaft — 23Rc62f Manual Transmission / Transaxle — 34Suspension — 22Tire And Wheel — 39Vf2cm Transfer — 44Can Communication — 45Multiplex Communication — 20Power Distribution — 5Power Steering — 29Steering Column — 29Air Conditioning — 108Door Lock — 88Engine Hood / Door — 16Engine Immobiliser — 47Exterior — 55Horn — 5Interior — 18Interior Panel — 8Lighting — 93Meter / Gauge / Display — 31Mirror — 22Other System — 24Pre-collision — 40Seat — 52Seat Belt — 40Sliding Roof — 26Supplemental Restraint Systems — 139Theft Deterrent — 20Window / Glass — 53Wiper / Washer — 24
~2min read
DESCRIPTION

Refer to TRAC OFF Indicator Light Remains ON (See page WIRING DIAGRAM ).

WIRING DIAGRAM

Refer to TRAC OFF Indicator Light Remains ON (See page CAUTION / NOTICE / HINT ).

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the skid control ECU (master cylinder solenoid), perform calibration (See page ). Inspect the fuses for circuits related to this system before performing ).
  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.
PROCEDURE

  1. CHECK CAN COMMUNICATION SYSTEM

NG

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)
OK

  1. INSPECT SKID CONTROL ECU (CSW TERMINAL)

(a) Disconnect the S1 skid control ECU (master cylinder solenoid) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

S1-9 (CSW) - Body ground

VSC OFF switch not pushed in

10 kΩ or higher

VSC OFF switch pushed in

Below 1 Ω
Text in Illustration

*a

Front view of wire harness connector

(to Skid Control ECU)

(c) Reconnect the S1 skid control ECU (master cylinder solenoid) connector.

NG

GO TO STEP 4
OK

  1. READ VALUE USING TECHSTREAM (TRAC/VSC OFF MODE)

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

ABS/VSC/TRAC

Tester Display

Measurement Item

Control Range

Diagnostic Note

TRAC/VSC Off Mode

TRAC/VSC off mode/ Normal, TRC OFF, Unknown or VSC OFF

Normal: Normal mode

TRC OFF: TRAC OFF mode

VSC OFF: VSC OFF mode

-

(f) Check that the mode display changes according to VSC OFF switch operation.

OK:

Display changes according to switch operation.

OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)
NG

REPLACE MASTER CYLINDER SOLENOID

  1. INSPECT VSC OFF SWITCH

NG

REPLACE VSC OFF SWITCH
OK

  1. INSPECT ROOF CONSOLE BOX ASSEMBLY (MASTER CYLINDER SOLENOID - VSC OFF SWITCH)

A

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASTER CYLINDER SOLENOID - ROOF CONSOLE BOX ASSEMBLY)
B

REPLACE ROOF CONSOLE BOX ASSEMBLY
C

REPLACE ROOF CONSOLE BOX ASSEMBLY

Test yourself

A quick Toyota Tacoma quiz: every answer comes with an explanation and a link to the manual page.