Toyota Tacoma Quiz
Brake Control / Dynamic Control Systems

Steering Angle Sensor Internal Circuit (C1433)

In this manual: Brake Control / Dynamic Control Systems
Introduction — 15Maintenance — 8Audio / Video — 94Garage Door Opener — 7Navigation / Multi Info Display — 84Park Assist / Monitoring — 86Brake — 50Brake Control / Dynamic Control Systems — 165Parking Brake — 52gr-fks Charging — 252gr-fks Cooling — 212gr-fks Emission Control — 132gr-fks Engine Control — 322gr-fks Engine Mechanical — 332gr-fks Exhaust — 92gr-fks Fuel — 422gr-fks Ignition — 62gr-fks Intake — 72gr-fks Lubrication — 152gr-fks Starting — 38Ac60e Automatic Transmission / Transaxle — 146Axle — 19Clutch — 20Cruise Control — 168Differential — 50Drive Shaft — 6Propeller Shaft — 23Rc62f Manual Transmission / Transaxle — 34Suspension — 22Tire And Wheel — 39Vf2cm Transfer — 44Can Communication — 45Multiplex Communication — 20Power Distribution — 5Power Steering — 29Steering Column — 29Air Conditioning — 108Door Lock — 88Engine Hood / Door — 16Engine Immobiliser — 47Exterior — 55Horn — 5Interior — 18Interior Panel — 8Lighting — 93Meter / Gauge / Display — 31Mirror — 22Other System — 24Pre-collision — 40Seat — 52Seat Belt — 40Sliding Roof — 26Supplemental Restraint Systems — 139Theft Deterrent — 20Window / Glass — 53Wiper / Washer — 24
2steps
~12min
1/5difficulty
Done 0 of 2
DESCRIPTION

Steering angle sensor (spiral cable with sensor sub-assembly) signals are sent to the skid control ECU (master cylinder solenoid) via the CAN communication system. When there is a malfunction in the CAN communication system, it is detected by the steering angle sensor (spiral cable with sensor sub-assembly) zero point malfunction diagnostic function.

DTC Code

DTC Detection Condition

Trouble Area

C1433

Either condition is met:

  1. With the IG1 terminal voltage at 9.5 to 17.4 V, the skid control ECU (master cylinder solenoid) receives an error signal from the steering angle sensor for 0.012 seconds.
  2. An open in the sensor power supply circuit for 1 second or more.

Steering angle sensor (spiral cable with sensor sub-assembly)
WIRING DIAGRAM

Refer to DTC C1432 (See page CAUTION / NOTICE / HINT ).

CAUTION / NOTICE / HINT

HINT:

  • When any of the speed sensors or the yaw rate and acceleration sensor (airbag sensor assembly) has trouble, DTCs for the steering angle sensor (spiral cable with sensor sub-assembly) may be stored even when the steering angle sensor (spiral cable with sensor sub-assembly) is normal. When DTCs for the speed sensors or yaw rate and acceleration sensor (airbag sensor assembly) are output together with DTCs for the steering angle sensor (spiral cable with sensor sub-assembly), inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering angle sensor (spiral cable with sensor sub-assembly).
PROCEDURE

  1. CHECK CAN COMMUNICATION SYSTEM

(a) Check for DTCs (See page ). Result ).

Result

Result

Proceed to

CAN DTC is not output

A

CAN DTC is output

B
B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)
A

  1. REPLACE STEERING ANGLE SENSOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY)

(a) Replace the steering angle sensor (spiral cable with sensor sub-assembly) (See page ).

NEXT

END

Test yourself

A quick Toyota Tacoma quiz: every answer comes with an explanation and a link to the manual page.