Toyota Tacoma Quiz
Brake Control / Dynamic Control Systems

Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) (C1275,...,C1414)

In this manual: Brake Control / Dynamic Control Systems
Introduction — 15Maintenance — 8Audio / Video — 94Garage Door Opener — 7Navigation / Multi Info Display — 84Park Assist / Monitoring — 86Brake — 50Brake Control / Dynamic Control Systems — 165Parking Brake — 52gr-fks Charging — 252gr-fks Cooling — 212gr-fks Emission Control — 132gr-fks Engine Control — 322gr-fks Engine Mechanical — 332gr-fks Exhaust — 92gr-fks Fuel — 422gr-fks Ignition — 62gr-fks Intake — 72gr-fks Lubrication — 152gr-fks Starting — 38Ac60e Automatic Transmission / Transaxle — 146Axle — 19Clutch — 20Cruise Control — 168Differential — 50Drive Shaft — 6Propeller Shaft — 23Rc62f Manual Transmission / Transaxle — 34Suspension — 22Tire And Wheel — 39Vf2cm Transfer — 44Can Communication — 45Multiplex Communication — 20Power Distribution — 5Power Steering — 29Steering Column — 29Air Conditioning — 108Door Lock — 88Engine Hood / Door — 16Engine Immobiliser — 47Exterior — 55Horn — 5Interior — 18Interior Panel — 8Lighting — 93Meter / Gauge / Display — 31Mirror — 22Other System — 24Pre-collision — 40Seat — 52Seat Belt — 40Sliding Roof — 26Supplemental Restraint Systems — 139Theft Deterrent — 20Window / Glass — 53Wiper / Washer — 24
3steps
~18min
2/5difficulty
Done 0 of 3
DESCRIPTION

Refer to DTCs C1401 and C1402 (See page ).

DTC Code

DTC Detection Condition

Trouble Area

C1275

C1276

Stored only during test mode.
  • Front speed sensor RH/LH
  • Front speed sensor rotor RH/LH (Front axle with ABS rotor bearing assembly RH/LH)

C1413

C1414

One of the following conditions is met:

  1. An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.
  2. At a vehicle speed of 20 km/h or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.
  3. At a vehicle speed of 10 km/h or more, noise occurs once per rotor rotation for 15 seconds or more.
  • Front speed sensor RH/LH
  • Skid control sensor wire
  • Speed sensor circuit
  • Front speed sensor rotor RH/LH (Front axle with ABS rotor bearing assembly RH/LH)
  • Skid control ECU (master cylinder solenoid)

HINT:

  • DTCs C1413 and C1275 are for the front speed sensor RH.
  • DTCs C1414 and C1276 are for the front speed sensor LH.
WIRING DIAGRAM

Refer to DTCs C1405 and C1406 (See page ).

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the skid control ECU (master cylinder solenoid), perform calibration (See page ).
  • Check the speed sensor signal after cleaning or replacement (See page ).
PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)

NG

GO TO STEP 9
OK

  1. READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR)

NG

GO TO STEP 5
OK

  1. PERFORM TEST MODE (SIGNAL CHECK)

(a) Perform the signal check in the Test Mode Procedure (See page ).

OK:

All test mode DTCs are cleared.

NG

GO TO STEP 5
OK

  1. RECONFIRM DTC

(a) Clear the DTCs (See page ).

(b) Turn the ignition switch off.

(c) Start the engine.

(d) Drive the vehicle at a speed of 40 km/h or more for at least 60 seconds.

(e) Check if the same DTC is output (See page ).

Result

Result

Proceed to

DTCs C1413 and C1414 are not output

A

DTCs C1413 and/or C1414 are output

B
A

USE SIMULATION METHOD TO CHECK
B

GO TO STEP 12

  1. CHECK FRONT SPEED SENSOR INSTALLATION

NG

INSTALL FRONT SPEED SENSOR CORRECTLY
OK

  1. INSPECT FRONT SPEED SENSOR TIP

NG

CLEAN OR REPLACE FRONT SPEED SENSOR
OK

  1. INSPECT FRONT SPEED SENSOR ROTOR

NG

CLEAN OR REPLACE FRONT AXLE WITH ABS ROTOR BEARING ASSEMBLY
OK

  1. INSPECT SKID CONTROL SENSOR WIRE

NG

REPLACE SKID CONTROL SENSOR WIRE
OK

  1. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

  1. INSPECT SKID CONTROL ECU (FR+, FL+ TERMINAL)

NG

REPLACE MASTER CYLINDER SOLENOID
OK

  1. RECONFIRM DTC

(a) Clear the DTCs (See page ).

(b) Turn the ignition switch off.

(c) Start the engine.

(d) Drive the vehicle at a speed of 40 km/h or more for at least 60 seconds.

(e) Check if the same DTC is output (See page ).

Result

Result

Proceed to

DTCs C1413 and C1414 are not output

A

DTCs C1413 and/or C1414 are output

B
A

USE SIMULATION METHOD TO CHECK
B

  1. REPLACE FRONT SPEED SENSOR

NEXT

  1. RECONFIRM DTC

(a) Clear the DTCs (See page ).

(b) Turn the ignition switch off.

(c) Start the engine.

(d) Drive the vehicle at a speed of 40 km/h or more for at least 60 seconds.

(e) Check if the same DTC is output (See page ).

Result

Result

Proceed to

DTCs C1413 and C1414 are not output

A

DTCs C1413 and/or C1414 are output

B
A

END
B

REPLACE FRONT AXLE WITH ABS ROTOR BEARING ASSEMBLY

Test yourself

A quick Toyota Tacoma quiz: every answer comes with an explanation and a link to the manual page.