Toyota Venza Quiz
Lighting (ext)

Disassembly

In this manual: Lighting (ext)
Introduction — 15Maintenance — 8Audio / Video — 102Garage Door Opener — 8Navigation / Multi Info Display — 81Park Assist / Monitoring — 50Brake (front) — 7Brake (rear) — 7Brake Control / Dynamic Control Systems — 79Brake System (other) — 28Parking Brake — 22Axle And Differential — 44Drive Shaft / Propeller Shaft — 24Mf1a Transfer / 4wd / Awd — 46U660e Automatic Transmission / Transaxle — 1241ar-fe Cooling — 311ar-fe Emission Control — 101ar-fe Engine Control — 1331ar-fe Engine Mechanical — 441ar-fe Fuel — 311ar-fe Intake / Exhaust — 211ar-fe Lubrication — 111ar-fe Starting — 16Cruise Control — 241ar-fe Battery / Charging — 162gr-fe Battery / Charging — 17Networking — 67Power Distribution — 8Power Assist Systems — 34Steering Column — 37Steering Gear / Linkage — 29Alignment / Handling Diagnosis — 4Front Suspension — 39Rear Suspension — 35Tire / Wheel — 4Tire Pressure Monitoring — 35Door / Hatch — 83Exterior Panels / Trim — 56Horn — 4Lighting (ext) — 89Mirror (ext) — 36Sliding Roof / Convertible — 26Window / Glass — 87Wiper / Washer — 30Door Lock — 85Heating / Air Conditioning — 82Interior Panels / Trim — 20Lighting (int) — 37Meter / Gauge / Display — 41Mirror (int) — 9Power Outlets (int) — 10Seat — 84Seat Belt — 43Supplemental Restraint Systems — 131Theft Deterrent / Keyless Entry — 155
~2min read
DISASSEMBLY PROCEDURE

1. REMOVE NO. 2 HEADLIGHT BULB (for Halogen Headlight)

(a) Turn the No. 2 headlight bulb in the direction indicated by the arrow shown in the illustration, and remove it.

NOTICE:

Do not touch the bulb glass.

2. REMOVE LIGHT CONTROL ECU (for HID Headlight)

(a) Turn the light control ECU in the direction indicated by the arrow shown in the illustration, and disconnect it.

NOTICE:

  • Do not apply excessive force using a tool.
  • Do not damage the O-ring or allow it to become contaminated with foreign matter. If the O-ring is damaged or contaminated, water may get into the headlight assembly, resulting in a malfunction of the light control ECU.

(b) Turn the socket of the light control ECU in the direction indicated by the arrow shown in the illustration, and remove it.

NOTICE:

Do not pull the light control ECU with the socket connected.

3. REMOVE DISCHARGE HEADLIGHT BULB (for HID Headlight)

(a) Release the set spring as shown in the illustration and remove the discharge headlight bulb.

NOTICE:

Do not touch the bulb glass.

4. REMOVE NO. 1 HEADLIGHT BULB (for Halogen Headlight)

(a) Turn the No. 1 headlight bulb in the direction indicated by the arrow shown in the illustration, and remove it.

NOTICE:

Do not touch the bulb glass.

5. REMOVE FRONT TURN SIGNAL LIGHT BULB

(a) for Halogen Headlight:

(1) Turn the front turn signal light socket with the front turn signal light bulb in the direction indicated by the arrow shown in the illustration, and remove them as a unit.

(b) for HID Headlight:

(1) Turn the front turn signal light socket with the front turn signal light bulb in the direction indicated by the arrow shown in the illustration, and remove them as a unit.

(c) Remove the front turn signal light bulb from the front turn signal light socket.

6. REMOVE FRONT SIDE MARKER LIGHT BULB

(a) Turn the front side marker light socket with the front side marker light bulb in the direction indicated by the arrow shown in the illustration, and remove them as a unit.

(b) Remove the front side marker light bulb from the front side marker light socket.

Test yourself

A quick Toyota Venza quiz: every answer comes with an explanation and a link to the manual page.