3-cyl. injection engine, timing belt drive (4-valve)

Lambda sensor

20steps
~120min
4/5difficulty
0204060801005037N·mlb·ft
Tightening torque found on this page
Done 0 of 20

Assembly overview - lambda sensor

Assembly overview - lambda sensor, vehicles with close-coupled emission control

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

  1. Engine
  2. Gasket
    • replace after removal
  3. Lambda sensor 1 before catalytic converter -GX10-

Consists of:

Lambda sensor -G39-

Lambda sensor heater -Z19-

Only grease the thread with "G 052 112 A3"; "G 052 112 A3" must not get onto the slots of the sensor body. Removing and installing "Lambda sensor 1 upstream of catalytic converter -GX10-". If leaking, cut open the sealing ring and replace it. 50 N·m
  1. Nut
    • Observe installation sequence
    • 23 N·m
  2. Lambda sensor 1 after catalytic converter -GX7-

Consists of:

Lambda sensor downstream of catalytic converter -G130-

Lambda sensor 1 downstream of catalytic converter heater -Z29-

Only grease the thread with "G 052 112 A3"; "G 052 112 A3" must not get onto the slots of the sensor body. Removing and installing "Lambda sensor 1 downstream of catalytic converter -GX7-". If leaking, cut open the sealing ring and replace it. 50 N·m
  1. Exhaust front pipe
    • Remove and install
  2. Subframe with bracket
    • Removing and installing → Suspension, Axles, Steering
  3. Bolt
    • Catalytic converter to bracket
    • 23 N·m
  4. Bolt
    • Bracket to cylinder block
    • 23 N·m
  5. Bracket
    • to cylinder block
    • Observe installation sequence
  6. Bracket
    • Observe installation sequence
  7. Bolt
    • 23 N·m

Assembly overview - lambda sensor, vehicles with underbody exhaust emission control

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

  1. Engine
  2. Gasket
    • replace after removal
  3. Lambda sensor 1 after catalytic converter -GX7-

Consists of:

Lambda sensor downstream of catalytic converter -G130-

Lambda sensor 1 downstream of catalytic converter heater -Z29-

Only grease the thread with "G 052 112 A3"; "G 052 112 A3" must not get onto the slots of the sensor body. Removing and installing. If leaking, cut open the sealing ring and replace it. 50 N·m
  1. Nut
    • 23 N·m
  2. Exhaust front pipe
    • Remove and install
  3. Mounting
    • Replace if damaged
  4. Subframe with bracket
    • Removing and installing → Suspension, Axles, Steering
  5. Lambda sensor 1 before catalytic converter -GX10-

Consists of:

Lambda sensor -G39-

Lambda sensor heater -Z19-

Only grease the thread with "G 052 112 A3"; "G 052 112 A3" must not get onto the slots of the sensor body. Removing and installing. If leaking, cut open the sealing ring and replace it. 50 N·m

Removing and installing lambda sensor

Removing and installing lambda sensor 1 upstream of catalytic converter -GX10-

Lambda sensor 1 upstream of catalytic converter -GX10- consists of:

  • Lambda sensor -G39-
  • Lambda sensor heater -Z19-

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Ring spanner set for lambda sensor -3337-

Removing

- Disconnect hose -1- from air filter housing.

- Remove air filter housing.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Unlock and disconnect connectors at bottom of lambda sensor 1 upstream of catalytic converter -GX10- -arrow-.

Connector color brown - lambda sensor 1 upstream of catalytic converter -GX10-

Connector color black - lambda sensor 1 downstream of catalytic converter -GX7-

- Route out wiring harness.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Unscrew lambda sensor 1 upstream of catalytic converter -GX10- -1- from catalytic converter -2-.

Installing

Installation is carried out in the reverse order. Observe the following:

Only grease the thread with "G 052 112 A3"; "G 052 112 A3" must not get onto the slots of the sensor body.

If leaking, cut open the sealing ring and replace it.

Tightening torques

  • "Assembly overview - lambda sensor"
VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

Removing and installing lambda sensor 1 downstream of catalytic converter -GX7-

Lambda sensor 1 downstream of catalytic converter -GX7- consists of:

  • Lambda sensor downstream of catalytic converter -G130-
  • Lambda sensor 1 downstream of catalytic converter heater -Z29-

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Ring spanner set for lambda sensor -3337-

Removing

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Unlock and disconnect connectors at top of lambda sensor 1 downstream of catalytic converter -GX7- -arrow-.

Connector color brown - lambda sensor 1 upstream of catalytic converter -GX10-

Connector color black - lambda sensor 1 downstream of catalytic converter -GX7-

- Route out wiring harness.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Unscrew lambda sensor 1 downstream of catalytic converter -GX7- -1- from below out of catalytic converter -2-.

Installing

Installation is carried out in the reverse order. Observe the following:

Only grease the thread with "G 052 112 A3"; "G 052 112 A3" must not get onto the slots of the sensor body.

If leaking, cut open the sealing ring and replace it.

Tightening torques

  • "Assembly overview - lambda sensor"
VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

Removing and installing lambda sensor, vehicles with underbody exhaust emission control

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Ring spanner set for lambda sensor -3337-

Removing

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Unlock and disconnect the respective connectors -arrow-.

Connector color brown - lambda sensor 1 upstream of catalytic converter -GX10-

Connector color black - lambda sensor 1 downstream of catalytic converter -GX7-

- Clip connector out of bracket.

- Route out wiring harness.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Unscrew the corresponding lambda sensor from catalytic converter -1-.

2 - Lambda sensor 1 upstream of catalytic converter -GX10-

3 - Lambda sensor 1 downstream of catalytic converter -GX7-

Installing

Installation is carried out in the reverse order. Observe the following:

Only grease the thread with "G 052 112 A3"; "G 052 112 A3" must not get onto the slots of the sensor body.

If leaking, cut open the sealing ring and replace it.

Tightening torques

  • "Assembly overview - lambda sensor"
VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)