3-cyl. injection engine, timing belt drive (4-valve)

Engine control module

5steps
~30min
2/5difficulty
0102030405097N·mlb·ft
Tightening torque found on this page
Done 0 of 5

Installation overview - Engine control module

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

  1. Bracket
    • Bracket secured to battery carrier
  2. Screw without anti-theft protection
    • for vehicles without anti-theft protection
    • installed left and right
    • Assignment → Electronic Parts Catalogue (ETKA)
    • 9 N·m
  3. Engine control module -J623-
    • Removing and installing, without anti-theft protection
    • Removing and installing, with anti-theft protection
  4. Rivets
    • Bracket attachment to engine control module
    • Assignment → Electronic Parts Catalogue (ETKA)
  5. Anti-theft bolt
    • for vehicles with anti-theft protection
    • installed left and right
    • Evenly tighten break-off bolts until the head shears off
    • Assignment → Electronic Parts Catalogue (ETKA)

Removing and installing engine control module -J623-

Required special tools, testers and equipment, and auxiliary items

  • Torque wrench -V.A.G 1331-


Note

  • If the engine control module -J623- is to be replaced, connect the → Vehicle diagnostic tester and perform "Guided function, replace engine control module".
  • When replacing the engine control module -J623-, it must be adapted to the electronic immobilizer → Vehicle diagnostic tester "Guided function".

Removing

- Switch off ignition.

- Remove battery → Electrical System.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Unscrew bolts -arrows- from battery carrier -2-.

- Tilt engine control module -1- forward together with bracket.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Press lock -1- in -arrow direction- with a screwdriver and hold it pressed.

- Use locking bracket -2- to unlock connector -3- from engine control module.

- To do so, press locking bracket -2- in -arrow direction-.

- Remove engine control module together with bracket.

Installing

Installation is carried out in the reverse order. Observe the following:

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

Tightening torques


Removing and installing engine control module -J623- with protective housing

Required special tools, testers and equipment, and auxiliary items

  • Torque wrench -V.A.G 1331-


Note

  • If the engine control module -J623- is to be replaced, connect the → Vehicle diagnostic tester and perform "Guided function, replace engine control module".
  • When replacing the engine control module -J623-, it must be adapted to the electronic immobilizer → Vehicle diagnostic tester "Guided function".

Removing

- Switch off ignition.

- Remove battery → Electrical System.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Open break-off bolts -arrows- using suitable workshop tools.

- Unscrew bolts -arrows- from battery carrier -2-.

- Tilt engine control module -1- forward together with bracket.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Press lock -1- in -arrow direction- with a screwdriver and hold it pressed.

- Use locking bracket -2- to unlock connector -3- from engine control module.

- To do so, press locking bracket -2- in -arrow direction-.

- Remove engine control module together with bracket.

Installing

Installation is carried out in the reverse order. Observe the following:

- Evenly tighten break-off bolts until the head shears off.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

Tightening torques