Guide Wheels, Tyres - General Information

Remove and install tire pressure sensor

~7min read
0102030405086N·mlb·ft
Tightening torque found on this page

Removing and installing tire pressure sensor, tire pressure sensor with valve

Removing

- Unscrew union nut -1-.

- Remove tire pressure sensor -2- from the rim well.

Installing


Caution!

Clean the valve hole before installing the tire pressure sensor.

VW UP. Ratgeber Räder, Reifen - Allgemeine Informationen

- Insert tire pressure sensor -2- with new seal and sealing washer and press it into the wheel rim at the points marked with -arrows-.

- Press tire pressure sensor -2- into the wheel rim at the points marked with -arrows-.

From outside, screw union nut -1- onto the tire pressure sensor.

VW UP. Ratgeber Räder, Reifen - Allgemeine Informationen

- Press tire pressure sensor -1- into the rim well at the points marked with -arrows- and tighten union nut to 8 N·m.


Caution!
  • Tighten the union nut only to the specified tightening torque.
  • Sealing washer -2- deforms slightly during tightening.
  • The sealing washer may only be installed once. Each time the sensor is reinstalled, replace the sealing washer including rubber seal with new parts.
  • Do not retighten the union nut, as this damages the seal and may cause leaks.

Tightening torques

  • "Assembly overview - tire pressure sensor, tire pressure sensor with valve"
VW UP. Ratgeber Räder, Reifen - Allgemeine Informationen

Removing and installing tire pressure sensor, tire pressure sensor without valve, service variant

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Torque wrench -V.A.G 1410-

Carry out the following work:

Removing

- Remove tire from wheel.

VW UP. Ratgeber Räder, Reifen - Allgemeine Informationen

Before further work, check which variant is installed.

  1. Service variant

In the service variant, the tire pressure sensor is attached to the valve with a bolt with internal Torx -1-.

If the service variant is installed, follow the repair procedure below.

  1. Production variant

In the production variant, the tire pressure sensor is attached to the valve with a square-head bolt with flat head -2-.

If the production variant is installed, follow the repair procedure below.

VW UP. Ratgeber Räder, Reifen - Allgemeine Informationen

- Unscrew bolt -arrow- for tire pressure sensor -1-.

- Hold metal valve with a counter-holder (for example a 2 mm twist drill).

Installing


Caution!

Clean the valve hole before installing the tire pressure sensor.

VW UP. Ratgeber Räder, Reifen - Allgemeine Informationen

- Press tire pressure sensor -1- onto the wheel rim and tighten -arrow-.

- Hold metal valve with a counter-holder (for example a 2 mm twist drill).


Note
  • After installation, perform a visual and fit check. The tire pressure sensor -1- must be screwed on without play and its support feet must rest in the well of the rim.
  • After installation, do not retighten the bolted connection to the tightening torque.

Tightening torques

  • "Assembly overview - Tire pressure sensor, tire pressure sensor without valve"
VW UP. Ratgeber Räder, Reifen - Allgemeine Informationen

Removing and installing tire pressure sensor, tire pressure sensor without valve, production variant

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Torque wrench -V.A.G 1410-

Carry out the following work:

Removing

- Remove tire from wheel.

VW UP. Ratgeber Räder, Reifen - Allgemeine Informationen

Before further work, check which variant is installed.

  1. Service variant

In the service variant, the tire pressure sensor is attached to the valve with a bolt with internal Torx -1-.

If the service variant is installed, follow the repair procedure below.

  1. Production variant

In the production variant, the tire pressure sensor is attached to the valve with a square-head bolt with flat head -2-.

If the production variant is installed, follow the repair procedure below.

VW UP. Ratgeber Räder, Reifen - Allgemeine Informationen

- Turn nut -1- counterclockwise until tire pressure sensor -2- can be removed.


Note
  • When turning nut -1-, the entire valve turns with it.
  • The tire pressure sensor must always be replaced together with the metal valve → Electronic Parts Catalog "ETKA".

- Remove metal valve.

Installing


Note
  • The tire pressure sensor must always be replaced together with the metal valve → Electronic Parts Catalog "ETKA".
  • The new metal valve is offered with a new bolt as a repair kit.

- Install metal valve.


Caution!

Clean the valve hole before installing the tire pressure sensor.

VW UP. Ratgeber Räder, Reifen - Allgemeine Informationen

- Press tire pressure sensor -1- onto the wheel rim and tighten with new bolt -arrow-.

- Hold metal valve with a counter-holder (for example a 2 mm twist drill).


Note
  • After installation, perform a visual and fit check. The tire pressure sensor -1- must be screwed on without play and its support feet must rest in the well of the rim.
  • After installation, do not retighten the bolted connection to the tightening torque.

Tightening torques

  • "Assembly overview - Tire pressure sensor, tire pressure sensor without valve"
VW UP. Ratgeber Räder, Reifen - Allgemeine Informationen

Removing and installing tire pressure sensor, removing and installing metal valve body

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Torque wrench -V.A.G 1410- and insert tool -V.A.G 1331-, SW 11.

- Insert metal valve with rubber seal through the rim from inside.

- Fit chamfered washer and union nut from outside and screw on by hand.

- Tighten union nut.


Note
  • If fitted, handle adhesive wheel trims carefully. The surface scratches easily.
  • If the wheel trim is damaged, replace the rim.

1) RDK direct measurement. Wheel electronics installed in the wheel on the metal valve; pressure and temperature values are sent and evaluated periodically.

2) RKA+ indirect measurement. No wheel electronics installed in the wheel. Comparison of rolling circumferences and vibration behavior of the individual wheels by analyzing signals from the ABS sensors. Loss of tire pressure is detected indirectly. When tire pressure changes, the speed and vibration behavior of the respective wheel change.

3) RKA indirect measurement. No wheel electronics installed in the wheel. Comparison of rolling circumferences of the individual wheels by analyzing signals from the ABS sensors. Loss of tire pressure is detected indirectly. When tire pressure changes, the speed of the respective wheel changes.

VW UP. Ratgeber Räder, Reifen - Allgemeine Informationen

- Secure against turning with counter-holder -1- (e.g. 2 mm Ø drill).


Note
  • If fitted, handle adhesive wheel trims carefully. The surface scratches easily.
  • If the wheel trim is damaged, replace the rim.

Tightening torques

VW UP. Ratgeber Räder, Reifen - Allgemeine Informationen

Removing and installing tire pressure sensor, wheel electronics system (RDK) Beru

View, Beru system


WARNING!

After using tire sealant, the wheel electronics of the affected wheel must be replaced.


WARNING!

Damaged wheel electronics must be replaced.

VW UP. Ratgeber Räder, Reifen - Allgemeine Informationen

- Press wheel electronics -1- into the well of the rim

- Screw on from behind the valve with microencapsulated bolt


Note
  • Replace microencapsulated bolt
  • Tighten microencapsulated bolt with 4 N·m on all models

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

VW UP. Ratgeber Räder, Reifen - Allgemeine Informationen

  • Torque wrench -V.A.G 1410- and insert tool -V.A.G 1410/1-

Tightening torques

VW UP. Ratgeber Räder, Reifen - Allgemeine Informationen

Removing and installing tire pressure sensor, Wheel Electronics System (RDK) Siemens


WARNING!

After using tire sealant, the wheel electronics of the affected wheel must be replaced.

  • The Siemens wheel electronics do not have a microencapsulated bolt
  • The wheel electronics are held in position by the union nut in the rim
  • The metal valve body serves as the antenna
  • The connection between the metal valve body and the wheel electronics must not be damaged

WARNING!

When pressing the wheel electronics into the drop center of the rim, hold the metal valve from behind by hand. The connection between the metal valve and the wheel electronics must not be interrupted or damaged. Damaged wheel electronics must be replaced.

- Press wheel electronics into the drop center

- Tighten wheel electronics to the metal valve with union nut

Tire sealant

Tire sealant, shelf life

The tire sealant in the bottle has a limited shelf life.

The best-before date is therefore indicated on the bottle -arrow-.

Replace the tire sealant when the best-before date has been reached (the tire sealant must not be older than 4 years).

If the bottle has been opened, e.g. after a tire puncture, it must also be replaced.

Observe the disposal regulations.

VW UP. Ratgeber Räder, Reifen - Allgemeine Informationen

Tire sealant, disposal

  • Tire sealant or residues must not be mixed with other waste/liquids
  • Any liquid residues of the tire sealant must be collected and filled into plastic containers. The plastic containers can be recycled together with the tire repair kits (if the expiry date has passed).
  • Take-back or recycling can be carried out through the existing workshop waste disposal systems
  • Contact the service provider or ask the waste officer of the distribution center or importer.