Hyundai Accent Quiz
Body

Front Door

In this manual: Body
Owner's Manual — 155SOHC Engines — 75DOHC Engines — 49Lubrication System — 14Cooling System — 23Emission Control — 3PCV Valve — 5Fuel system — 44Ignition System — 12Clutch — 17Manual transmission — 14Automatic transmission — 24Axle Shafts and Drive Shafts — 17Suspension — 31Steering — 45Brake System — 39Body — 23Air Conditioning System — 32Electrical Equipment — 54Appendix — 9Wiring Diagrams — 3
~2min read

Removal and installation

PROCEDURE

1. Освободите скобу крепления ручки стеклоподъемника и снимите ручку. Скоба освобождается,

1. Release the window regulator handle clip and remove the handle. The clip is released by inserting a clean cloth between the handle and the door trim and, pulling the cloth back and forth against the ends of the clip, hooking and releasing it. Pull the handle toward you so that, after the clip is released, it slides off the splines of the window regulator shaft.

2. Выверните винт крепления внутренней ручки, затем нажмите ручку в направлении

2. Remove the inside handle screw, then press the handle toward the door hinges and remove it from the door trim.

3. Снимите внутреннюю крышку и наружное зеркало заднего вида.

3. Remove the inside cover and the outside rearview mirror.

4. Выверните винты крепления обивки двери.

4. Remove the door trim mounting screws.

5. Вставьте съемник обивки двери между обивкой двери и дверью и освободите пистоны.

5. Insert a door trim remover between the door trim and the door and release the clips. Disconnect the electrical connectors.

6. Снимите обивку двери и опустите стекло.

6. Remove the door trim and lower the window.

7. Выверните три винта и снимите динамик с передней двери.

7. Remove the three screws and remove the speaker from the front door.

8. Снимите оконное стекло.

8. Remove the window glass.

9. Снимите наружную влагозащитную полосу с двери.

9. Remove the outer door weatherstrip from the door.

10. Выверните винты и снимите стеклоподъемник.

10. Remove the screws and remove the window regulator.

11. Снимите направляющую стекла двери.

11. Remove the door glass run.

12. Снимите тягу и активатор замка от наружной ручки двери.

12. Disconnect the rod and the lock activator from the outside door handle.
13. Remove the door latch, the door lock actuator and the outside door handle.

14. Установка проводится в последовательности, обратной снятию.

14. Install in the reverse order of removal.

Door Position Adjustment

PROCEDURE

1. Check that the door closes easily and properly. If the door has play, tighten the door hinge mounting bolts.
2. If it is necessary to adjust the door position relative to the adjacent surfaces, adjust the hinges using special tool 09793–21000.

Предупреждение

Attach protective tape to the fender edges opposite the door hinge.

Door Striker Plate

PROCEDURE

1. Check that the door closes easily and properly. If the door lock engages the striker plate with difficulty, remove the striker plate mounting screws and move the plate horizontally and vertically until the door closes normally.

2. Регулировку положения двери относительно смежных поверхностей проводите перемещением

2. Adjust the door position relative to the adjacent surfaces by moving the striker plate vertically.

Door Glass

PROCEDURE

Если стекло двери неравномерно закрывается, отрегулируйте угол установки стекла

If the window glass closes unevenly, adjust the angle of the glass installation from the front to the rear.

Test yourself

A quick Hyundai Accent quiz: every answer comes with an explanation and a link to the manual page.