Kia Stinger CK Quiz
Windshield Wiper/Washer

eCall Module

In this manual: Windshield Wiper/Washer
General Information — 8Maintenance — 27Engine Mechanical System — 47Engine Electrical System — 19Emission Control System — 12Engine Control System/Fuel System — 51Automatic Transmission System — 34All-Wheel Drive (AWD) System — 7Drive Shaft and Axle — 15Suspension System — 25Steering — 8Restraints — 19Brake System — 22Body (Interior and Exterior) — 47Front Seat Belt — 63Body Electrical System — 99Windshield Wiper/Washer — 11Heating, Ventilation, and Air Conditioning — 32
34steps
~204min
5/5difficulty
Done 0 of 34

Components and Component Location

Component

Repair Procedures

Removal

eCall module

  1. Disconnect the negative (-) battery terminal.

  2. Remove the glove box housing.

    (Refer to Body - "Glove Box Housing")

  3. Disconnect the connectors from the eCall module (A).

  4. Remove the eCall module (A) after loosening the mounting screw and nuts.

eCall Antenna

  1. Disconnect the negative (-) battery terminal.

  2. Remove the driver airbag module assembly.

    (See Body — "Main Airbag Assembly")

  3. Remove the eCall antenna (A) after loosening the mounting screws and disconnect the connector (B).

Emergency Call Speaker

  1. Disconnect the negative (-) battery terminal.

  2. Remove the center speaker grille (A) using a remover.

  3. Disconnect the protector connector (A) and the auto light sensor and photo sensor connector (B).

  4. Remove the eCall speaker (A) after loosening the mounting screws.

  5. Disconnect the eCall speaker connector (B).

Replacement

Replacing the eCall Backup Battery (BUB)

  1. Disconnect the negative (-) battery terminal.

  2. Remove the eCall module.

  3. To replace the backup battery, remove it after removing the backup battery compartment cover (A).

Installation

eCall module

  1. Install the eCall module.

  2. Connect the connectors to the eCall module.

  3. Install the glove box housing.

  4. Connect the negative (-) battery terminal.

eCall Antenna

  1. Install the eCall antenna.

  2. Connect the eCall antenna connector.

  3. Install the driver airbag module assembly.

  4. Connect the negative (-) battery terminal.

Emergency Call Speaker

  1. Connect the eCall speaker connector.

  2. Install the eCall speaker.

  3. Connect the auto light sensor connector and the photo sensor connector.

  4. Install the center speaker grille.

  5. Connect the negative (-) battery terminal.

Inspection

Inspection (with KDS)

  1. In the body electrical system, faults can be quickly diagnosed using the Korean Diagnostic System (KDS).

    The Diagnostic System (KDS) provides the following information.

    1. Self-Diagnosis: Checks for malfunctions and Diagnostic Trouble Codes (DTCs).

    2. Current Data: Checks the input/output status of the system.

    3. Actuation Test: Checks the operating condition of the system.

    4. Additional Function: Controls other functions, including system setting parameters and zero point adjustment.

  2. Select "Vehicle Model" and "Telematics System" to inspect in order using the tester.

  3. Select the "Current Data" menu to check the current input/output data.

eCall Test Mode

Press the SOS TEST button to activate the audible guidance and test the eCall system. Refer to the manual.

In the Test Call step, which is the final step of the test mode, press the SOS button following the voice guidance to send the faulty component data to the call center.

To exit the test mode, press the SOS TEST button again during the voice guidance.

  1. Test mode operating conditions:

    1. The vehicle battery is connected properly.

    2. One minute has passed after ignition ON.

    3. The vehicle remains stationary for 1 minute or more.

  2. Conditions preventing test mode operation:

    1. A PSAP call is in progress.

    2. Callback Mode: After a successful call, the eCall system enters callback mode and stands by for 120 minutes to receive calls from the call center.

    3. Test mode is automatically terminated when the vehicle speed reaches 1 km/h or more, or after traveling 300 m or more.

    4. Less than two minutes have passed since the previous test call was completed.

  3. Test mode operation sequence (voice guidance):

    1. LED Test

    2. Speaker Test

    3. MIC Test

    4. BUB (Back-Up Battery built into eCall unit) Test (No separate notification is given if the BUB is in normal condition.)

    5. Test Call (Pressing the SOS button sends the test result to the PSAP.)

Inspecting the Backup Battery

The backup battery (BUB) built into the eCall system has a limited service life, and its charging/discharging performance may deteriorate after prolonged use.

The backup battery ensures operation of the eCall system when the vehicle battery cannot be used due to an accident. Be sure to inspect the backup battery if the red LED comes on, and replace it if necessary.

Test yourself

A quick Kia Stinger CK quiz: every answer comes with an explanation and a link to the manual page.