Transaxle & transmission CVT: RE0F10B

P0715 input speed sensor A

In this manual: Transaxle & transmission CVT: RE0F10B
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~3min read

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION PROCEDURE

CAUTION:
Always drive vehicle at a safe speed.
NOTE:

If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test.

After the repair, perform the following procedure to confirm the malfunction is eliminated.

1.CHECK DTC DETECTION

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON. 2. Select “DATA MONITOR”.

3. Start engine and maintain the following conditions for at least 5 consecutive seconds.

VEHICLE SPEED : 10 km/h or more ACC PEDAL OPEN : More than 1.0/8 RANGE : “D” position
ENG SPEED : 450 rpm or more Driving location : Driving the vehicle uphill (increased engine load) will help maintain the driving conditions required for this test.

Follow the procedure “With CONSULT-III”.With GST


Follow the procedure “With CONSULT-III”.

Is “P0715” detected? YES >> Go to TM-204, "Diagnosis Procedure".

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

Diagnosis Procedure

1. CHECK POWER AND SENSOR GROUND 1. Turn ignition switch OFF. 2. Disconnect the primary speed sensor harness connector. 3. Turn ignition switch ON.

4. Check voltage between primary speed sensor harness connector terminals.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 2.

NO >> GO TO 6.

2. CHECK TCM INPUT SIGNAL 1. Turn ignition switch OFF. 2. Connect the primary speed sensor harness connector. 3. Start engine. 4. Lift up the vehicle.

5. Check frequency of primary speed sensor.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 9.

NO >> GO TO 3.

3. CHECK HARNESS BETWEEN TCM AND PRIMARY SPEED SENSOR (PART 1) 1. Turn ignition switch OFF. 2. Disconnect TCM connector and primary speed sensor harness connector.

3. Check continuity between TCM connector terminal and primary speed sensor harness connector terminal.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace damaged parts.

4. CHECK HARNESS BETWEEN TCM AND PRIMARY SPEED SENSOR (PART 2)

Check continuity between TCM connector terminal and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace damaged parts.

5. CHECK CVT UNIT CIRCUIT 1. Disconnect CVT unit connector.

2. Check continuity between CVT unit connector terminals and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace damaged parts.

6. CHECK HARNESS BETWEEN PRIMARY SPEED SENSOR (POWER) AND IPDM E/R (PART 1) 1. Turn ignition switch OFF. 2. Disconnect IPDM E/R connector.

3. Check continuity between primary speed sensor vehicle side harness connector terminal and IPDM E/R vehicle side harness connector terminal.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace damaged parts.

7. CHECK HARNESS BETWEEN PRIMARY SPEED SENSOR (POWER) AND IPDM E/R (PART 1)

Check continuity between primary speed sensor vehicle side harness connector terminal and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 8.

NO >> Repair or replace damaged parts.

8.DETECT MALFUNCTIONING ITEMS

Check the following. Refer to PG-15, "Wiring Diagram - IGNITION POWER SUPPLY -".

• IPDM E/R
• 10A fuse (No.55, located in the IPDM E/R) • Harness for short or open between IPDM E/R and ignition switch • Ignition switch

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident" NO >> Repair or replace damaged parts.

9.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident".

Is the inspection result normal? YES >> Replace primary speed sensor. Refer to TM-290, "Removal and Installation".

NO >> Repair or replace damaged parts.