Transmission & Driveline

Additional Service When Replacing Tcm

19steps
~114min
5/5difficulty
Done 0 of 19
Description

Always perform the following items when the TCM is replaced. For work procedure, refer to Work Procedure.

TCM PROGRAMMING

  • Since vehicle specifications are not yet written in a new TCM, it is necessary to write them with CONSULT.

SAVING AND WRITING OF TCM DATA (IP CHARACTERISTICS VALUE)

  • TCM performs accurate control by retrieving data (inherent characteristic value) of each solenoid. For this reason, it is necessary to save data of current TCM in CONSULT before replacing the TCM. After this, the saved data must be written in new TCM.

Work Procedure
  • ASIST on the CONSULT has been synchronized to the current date.

  • All CONSULT software updates (if any) have been installed.

SAVE THE TCM DATA (IP CHARACTERISTICS VALUE)

With CONSULT

  1. Turn ignition switch OFF and wait for 10 seconds.

  2. Turn ignition switch ON.

  3. Connect CONSULT.

  4. Select “Work Support” in “TRANSMISSION”.

  5. Select “READ IP CHARA - REPLACEMENT TCM”.

  6. Select “START”.

  7. Select “END” to finish.

>>

GO TO 2.

SAVE ‘OPERATION LOG’

With CONSULT

Save Operation Log, according to the procedure of “Programming” in CONSULT Operation Manual.

>>

GO TO 3.

REPLACE TCM

  1. Ignition switch OFF.

  2. Replace the TCM. Refer to Removal and Installation.

>>

GO TO 4.

CHECK ‘OPERATION LOG’

With CONSULT

Check Operation Log saved before replacing A/T assembly, according to the procedure of “Programming” in CONSULT Operation Manual.

Is there an applicable Operation Log in the Saved Data List?

YES>>

GO TO 5.

NO>>

GO TO 6.

PERFORM TCM PROGRAMMING

With CONSULT

Perform TCM programming, according to “Programming” of CONSULT Operation Manual. Refer to CONSULT Operation Manual.

  • Ignition switch: ON

  • Electric load: OFF

  • Brake pedal: Not depressed

  • Battery voltage: 12 – 13.5 V (Be sure to check the value of battery voltage by selecting “BATTERY VOLT” in “Data monitor” of CONSULT.)

>>

GO TO 8.

READ IN TCM ROM DATA ID BY ‘EPC LINKED’

With CONSULT

Obtain TCM ROM data ID by EPC (service parts catalog), according to the procedure of ‘EPC linked’ in CONSULT Operation Manual. Refer to CONSULT Operation Manual.

>>

GO TO 7.

PERFORM TCM PROGRAMMING (EPC LINKED)

With CONSULT

Perform TCM programming according to the procedure of EPC linked' in CONSULT Operation Manual. Refer to CONSULT Operation Manual.

  • Ignition switch: ON

  • Electric load: OFF

  • Brake pedal: Not depressed

  • Battery voltage: 12 – 13.5 V (Be sure to check the value of battery voltage by selecting “BATTERY VOLT” in “Data monitor” of CONSULT.)

>>

GO TO 8.

WRITE THE TCM DATA (IP CHARACTERISTICS VALUE)

With CONSULT

  1. Verify Nissan Murano vehicle is in “Park” (P), then turn ignition switch OFF and wait for 10 seconds.

  2. Turn ignition switch ON.

  3. Select “Work Support” in “TRANSMISSION”.

  4. Select “WRITE IP CHARA - REPLACEMENT TCM”.

  5. Select “START”.

  6. Select “START” again.

  7. Select “YES” on the Information window.

  8. Select “END”.

>>

GO TO 9.

PERFORM CALIBRATION OF G SENSOR

Perform G-Sensor Calibration. Refer to Description.

>>

GO TO 10.

PERFORM CLUTCH POINT LEARNING

Perform Clutch Point Learning. Refer to Description.

>>

GO TO 11.

PERFORM SELECT LEARNING (DRIVE/REVERSE LEARNING)

  1. Perform Select Learning. Refer to Work Procedure.

  2. Clear any DTCs that may have set and then test drive the Nissan Murano vehicle.

>>

WORK END