Network Operation

Power Window Master Switch Communication Stop (B1206)

~4min read

DESCRIPTION

This DTC is stored when LIN communication between the multiplex network master switch assembly and the main body ECU (multiplex network body ECU) is cut off for 10 seconds or more.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

B1206

Main Switch P/W Communication Stop

No communication between the multiplex network master switch assembly and the main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Multiplex Network Master Switch Assembly
  • Main body ECU (multiplex network body ECU)
  • Instrument Panel Junction Block Assembly
  • Wire harness or connector
  • ECU-B No. 2 fuse

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Check the fuses for the circuits related to this system before performing the following procedure.
  • If the Main Body ECU (Multiplex Network Body ECU) has been replaced, refer to the registration section.*1

    Click here

    • *1: with Smart Key System

PROCEDURE

  1. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

(a) Remove the instrument panel junction block assembly.

Click here

*a

Component without wire harness connected

(instrument panel junction block assembly)

-

-

(b) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

(c) Measure the resistance according to the value(s) in the table below.

HINT:

This check is used to inspect the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the integrated main body ECU (multiplex network body ECU).

Standard resistance:

Tester Connection

Condition

Specified Condition

3H-25 - MB-16 (LIN2)

Always

Below 1 Ω

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

(a) Disconnect the J6 connector from the multiplex network main switch assy.

(b) Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the check. To enter sleep mode, turn the ignition switch from ON to OFF and wait at least 180 seconds without operating any switches.

Standard resistance:

Tester Connection

Ignition switch position

Specified Condition

3H-25 - J6-17 (LIN1)

Ignition Switch in OFF position

Below 1 Ω

J6-17 (LIN1) or 3H-25 - Body ground

Ignition Switch in OFF position

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - BATTERY, BODY GROUND)

(a) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

J6-11 (B) - J6-12 (GND)

Always

11 à 14 V

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

J6-12 (GND) - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE MULTIPLEX NETWORK MAIN SWITCH ASSEMBLY

(a) Replace the multiplex network main switch assembly.

Click here

NEXT
  1. CHECK WHETHER DTCs ARE OUTPUT

(a) Clear the DTCs.

Click here

Body Electrical > Main Body > Clear DTCs

(b) Check the DTCs again.

Body Electrical > Main Body > Trouble Codes

OK:

DTC B1206 is not output.

OK

END (MULTIPLEX NETWORK MAIN SWITCH ASSEMBLY IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)