Network Operation

No Response from ID Code Box (B2789)

~4min read

DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key system ECU assembly) and the ID code box (immobilizer ECU) is interrupted for more than 10 seconds.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

B2789

No Response from ID Code Box

No communication between the certification ECU (smart key system ECU assembly) and the ID code box (immobilizer ECU) for at least 10 seconds.

  • ID Code Box (Immobilizer ECU)
  • Certification ECU (Smart Key ECU Assy)
  • Wire harness or connector
  • ECU-B No. 1 Fuse

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Check the fuses for the circuits related to this system before performing the following procedure.
  • While using the Techstream with the ignition switch in the OFF position, connect the Techstream to the DLC3 and turn a courtesy light switch ON and OFF at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle starts. Then select the vehicle type manually and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a courtesy light switch between ON and OFF at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
  • When replacing the certification ECU (smart key system ECU assembly) or the ID code box (immobilizer ECU), refer to Registration.

    Click here

PROCEDURE

  1. CHECK WIRE HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY SYSTEM ECU ASSEMBLY) - ID CODE BOX (IMMOBILIZER ECU))

(a) Disconnect the F1 connector from the certification ECU (smart key ECU assembly).

(b) Disconnect the F21 connector from the ID code box (immobilizer ECU).

(c) Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the check. To enter sleep mode, turn the ignition switch from ON to OFF and wait at least 180 seconds without operating any switches.

Standard resistance:

Tester Connection

Ignition switch position

Specified Condition

F1-13 (LIN) - F21-2 (LIN1)

Ignition Switch in OFF position

Below 1 Ω

F1-13 (LIN) or F21-2 (LIN1) - Body Ground

Ignition Switch in OFF position

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILIZER ECU) - BATTERY, BODY GROUND)

(a) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

F21-1 (+B) - F21-5 (GND)

Always

11 à 14 V

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F21-5 (GND) - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

(a) Replace the ID code box (immobilizer ECU).

HINT:

Refer to Registration.

Click here

NEXT
  1. REGISTER ECU CODE RECORD

(a) Register the identification codes in the ECUs.

HINT:

Refer to Registration.

Click here

NEXT
  1. CHECK WHETHER DTCs ARE OUTPUT

(a) Clear the DTCs.

Click here

Body Electrical > Smart Key > Clear DTCs

(b) Check the DTCs again.

Body Electrical > Smart Key > Trouble Codes

OK:

DTC B2789 is not output.

OK

END (ID CODE BOX (IMMOBILISER ECU) WAS FAULTY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)