Network Operation

Communication Malfunction Between ECUs Connected by LIN (B2785)

~5min read

DESCRIPTION

If the certification ECU (smart key ECU assembly) detects a communication error with an ECU connected to the certification bus lines for 7 seconds or more, DTC B2785 is stored.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

B2785

Communication Malfunction Between LIN-Connected ECUs

One of the following conditions is met

  • LIN communication errors between ECUs.
  • Open in the communication lines.
  • Short circuit in the communication lines.
  • The certification ECU (smart key ECU assembly) detects a communication error with the ECUs connected to the certification bus lines for 7 seconds or more.
  • Certification ECU (Smart Key ECU Assy)
  • Steering lock ECU (steering lock actuator or upper bracket assembly)
  • ID Code Box (Immobilizer ECU)
  • Wire harness or connector
  • AM2 Fuse
  • STRG LOCK Fuse
  • ECU-B No. 1 Fuse
DTC Detection Conditions

Vehicle Operating Conditions

Sequence 1

Sequence 2

Sequence 3

Sequence 4

Diagnostic Condition

-

○

○

○

○

Malfunction Status

LIN communication errors between ECUs

○

-

-

-

Open in the communication lines

-

○

-

-

Short circuit in the communication lines

-

-

○

-

The certification ECU (smart key ECU assembly) detects a communication error with an ECU connected to the certification bus lines

-

-

-

○

Detection Duration

-

-

-

7 seconds or more

Number of Trips

1 trip(s)

1 trip(s)

1 trip(s)

1 trip(s)

HINT:

The DTC is output when the conditions for any one of the sequences in the table above are met.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Check the fuses for the circuits related to this system before performing the following procedure.
  • Before performing the check, make sure that DTC B2786, B2789 or B278C is not stored.

    Click here

  • While using the Techstream with the ignition switch in the OFF position, connect the Techstream to the DLC3 and turn a courtesy light switch ON and OFF at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle starts. Then select the vehicle type manually and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a courtesy light switch between ON and OFF at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
  • If the certification ECU (smart key ECU assembly), ID code box (immobilizer ECU) or steering lock ECU (steering lock actuator or upper support assembly) is replaced, refer to the registration section.

    Click here

PROCEDURE

  1. CHECK WIRE HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - EACH ECU)

(a) Disconnect the F1 connector from the certification ECU (smart key ECU assembly).

(b) Disconnect connector F78 of the steering lock ECU (steering lock actuator or upper support assembly).

(c) Disconnect the F21 connector from the ID code box (immobilizer ECU).

(d) Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the check. To enter sleep mode, turn the ignition switch from ON to OFF and wait at least 180 seconds without operating any switches.

Standard resistance:

Tester Connection

Ignition switch position

Specified Condition

F1-13 (LIN) - F21-2 (LIN1)

Ignition Switch in OFF position

Below 1 Ω

F1-13 (LIN) - F78-5 (LIN)

Ignition Switch in OFF position

Below 1 Ω

F1-13 (LIN), F78-5 (LIN) or F21-2 (LIN1) - Body ground

Ignition Switch in OFF position

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK DTC (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER SUPPORT ASSEMBLY)

(a) Reconnect connector F1 of the certification ECU (smart key ECU assembly).

(b) Reconnect the F21 connector to the ID code box (immobilizer ECU).

(c) Clear the DTCs.

Click here

Body Electrical > Smart Key > Clear DTCs

(d) Check the DTCs again.

Body Electrical > Smart Key > Trouble Codes

Result:

Result

Proceed to

DTC B2785 is output

A

DTC B2785 is not output

B

B

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER SUPPORT ASSEMBLY)

A
  1. CHECK DTC (ID CODE BOX (IMMOBILIZER ECU)

(a) Reconnect the F78 steering lock ECU connector (steering lock actuator or upper support assy).

(b) Disconnect the F21 connector from the ID code box (immobilizer ECU).

(c) Clear the DTCs.

Click here

Body Electrical > Smart Key > Clear DTCs

(d) Check the DTCs again.

Body Electrical > Smart Key > Trouble Codes

Result:

Result

Proceed to

DTC B2785 is output

A

DTC B2785 is not output

B

A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)

B

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)