ECU Terminals
ECU TERMINALS
CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
*A |
1-Connector System |
- |
- |
*A |
2-Connector System |
- |
- |
(a) Disconnect the MB connector of the main body ECU (multiplex network body ECU).
Click here![]()
(b) Measure the voltage and resistance according to the value(s) specified in the table below.
HINT:
Measure the values at the wire harness side with the connectors disconnected.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
MB-11 (GND1) - Body ground |
- |
Ground |
Always |
Below 1 Ω |
MB-31 (BECU) - Body ground |
- |
Battery power supply |
Always |
11 à 14 V |
MB-30 (ACC) - Body ground |
- |
ACC power supply |
Ignition Switch in ACC position |
11 à 14 V |
Ignition Switch in OFF position |
Below 1 V |
|||
MB-32 (IG) - Body ground |
- |
IG power supply |
Ignition Switch in ON position |
11 à 14 V |
Ignition Switch in OFF position |
Below 1 V |
(c) Reconnect the MB connector of the main body ECU (multiplex network body ECU).
Click here![]()
(d) Check the pulses according to the values shown in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
3H-25 (LIN2) - Body Ground |
LG - Body ground |
LIN communication line |
Ignition Switch in ON position |
Pulse generation |
3D-17 (LIN2) - Body Ground*1 |
P - Body ground |
LIN communication line |
Ignition Switch in ON position |
Pulse generation |
- *1: with double lock system
CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for driver door)
(a) Disconnect the J2 connector from the power window motor assembly (for driver door).
(b) Measure the voltage and resistance according to the value(s) specified in the table below.
HINT:
Measure the values at the wire harness side with the connector disconnected.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
J2-2 (B) - Body ground |
L - Body ground |
Battery power supply |
Always |
11 à 14 V |
J2-1 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
(c) Reconnect the J2 connector to the power window motor assembly (for driver door).
(d) Check the pulses according to the values shown in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
J2-9 (LIN) - Body Ground |
R - Body ground |
LIN communication line |
Ignition Switch in ON position |
Pulse generation |
CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for front passenger side)
(a) Disconnect the I2 connector from the power window motor assembly (for front passenger door).
(b) Measure the voltage and resistance according to the value(s) specified in the table below.
HINT:
Measure the values at the wire harness side with the connector disconnected.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
I2-2 (B) - Body ground |
L - Body ground |
Battery power supply |
Always |
11 à 14 V |
I2-1 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
(c) Reconnect the I2 connector to the power window motor assembly (for front passenger door).
(d) Check the pulses according to the values shown in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
I2-9 (LIN) - Body Ground |
P - Body ground |
LIN communication line |
Ignition Switch in ON position |
Pulse generation |
CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for rear RH door)
(a) Disconnect the K2 connector from the power window motor assembly (for rear right door).
(b) Measure the voltage and resistance according to the value(s) specified in the table below.
HINT:
Measure the values at the wire harness side with the connector disconnected.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
K2-2 (B) - Body ground |
R - Body ground |
Battery power supply |
Always |
11 à 14 V |
K2-1 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
(c) Reconnect the K2 connector to the power window motor assembly (for rear right door).
(d) Check the pulses according to the values shown in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
K2-9 (LIN) - Body Ground |
LG - Body ground |
LIN communication line |
Ignition Switch in ON position |
Pulse generation |
CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (rear LH door)
(a) Disconnect the L2 connector from the power window motor assembly (for rear left door).
(b) Measure the voltage and resistance according to the value(s) specified in the table below.
HINT:
Measure the values at the wire harness side with the connector disconnected.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
L2-2 (B) - Body ground |
R - Body ground |
Battery power supply |
Always |
11 à 14 V |
L2-1 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
(c) Reconnect the L2 connector to the power window motor assembly (for rear left door).
(d) Check the pulses according to the values shown in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
L2-9 (LIN) - Body Ground |
LG - Body ground |
LIN communication line |
Ignition Switch in ON position |
Pulse generation |
INSPECT MULTIPLEX NETWORK MAIN SWITCH ASSY
(a) Disconnect the J6 connector from the multiplex network main switch assy.
(b) Measure the voltage and resistance according to the value(s) specified in the table below.
HINT:
Measure the values at the wire harness side with the connector disconnected.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
J6-11 (B) - Body Ground |
B - Body ground |
Battery power supply |
Always |
11 à 14 V |
J6-12 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
(c) Reconnect the J6 connector to the multiplex network main switch assy.
(d) Check the pulses according to the values shown in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
J6-17 (LIN1) - Body Ground |
P - Body ground |
LIN communication line |
Ignition Switch in ON position |
Pulse generation |
J6-16 (LIN2) - Body Ground |
R - Body ground |
LIN communication line |
Ignition Switch in ON position |
Pulse generation |
INSPECT CERTIFICATION ECU (INTELLIGENT KEY ECU ASSEMBLY) (with Smart Key System)
(a) Disconnect the F1 connector from the certification ECU (smart key ECU assembly).
(b) Measure the voltage and resistance according to the value(s) specified in the table below.
HINT:
Measure the values at the wire harness side with the connector disconnected.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F1-18 (E) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
F1-4 (+B) - Body ground |
L - Body ground |
Power source +B |
Always |
11 à 14 V |
(c) Reconnect the F1 connector to the certification ECU (smart key ECU assembly).
(d) Check the pulses according to the values shown in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F1-13 (LIN) - Body Ground |
B - Body ground |
LIN communication line |
Ignition Switch in ON position |
Pulse generation |
CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER SUPPORT ASSEMBLY) (with Smart Key System)
(a) Disconnect the F78 steering lock ECU connector (steering lock actuator or upper support assy).
(b) Measure the voltage and resistance according to the value(s) specified in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F78-1 (GND) - Body ground |
W-B Body Ground |
Ground |
Always |
Below 1 Ω |
F78-7 (B) - Body ground |
L - Body ground |
Battery power supply |
Always |
11 à 14 V |
(c) Reconnect the F78 connector of the steering lock ECU (steering lock actuator or upper support assembly).
(d) Check the pulses according to the values shown in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F78-5 (LIN) - Body Ground |
V - Body ground |
LIN communication line |
Ignition Switch in ON position |
Pulse generation |
CHECK ID CODE BOX (ENGINE IMMOBILISER CODE ECU) (with Smart Key System)
(a) Disconnect the F21 connector from the ID code box (immobilizer code ECU).
(b) Measure the voltage and resistance according to the value(s) specified in the table below.
HINT:
Measure the values at the wire harness side with the connector disconnected.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F21-5 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
F21-1 (+B) - Body ground |
W - Body Ground |
Power source +B |
Always |
11 à 14 V |
(c) Reconnect the F21 connector to the ID code box (immobilizer code ECU).
(d) Check the pulses according to the values shown in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F21-2 (LIN1) - Body Ground |
B - Body ground |
LIN communication line |
Ignition Switch in ON position |
Pulse generation |
CHECK DOUBLE LOCK DOOR CONTROL RELAY (with double lock system)
(a) Disconnect connector F14 of the double lock control relay assembly.
(b) Measure the voltage and resistance according to the value(s) specified in the table below.
HINT:
Measure the values at the wire harness side with the connector disconnected.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F14-12 (+B) - Body ground |
BE - Body ground |
Battery power supply |
Always |
11 à 14 V |
F14-11 (CPUB) - Body ground |
SB - Body ground |
Battery power supply |
Always |
11 à 14 V |
F14-7 (GND) - Body ground |
LA - Body ground |
Ground |
Always |
Below 1 Ω |
(c) Reconnect connector F14 of the double lock control relay assembly.
(d) Check the pulses according to the values shown in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F14-9 (LIN) - Body Ground |
P - Body ground |
LIN communication line |
Double lock disabled |
Pulse generation |