Door Lock

System Description

~7min read

SYSTEM DESCRIPTION

REMOTE POWER DOOR LOCK SYSTEM

The remote power door lock control system can be used to lock and unlock all doors remotely. The system is operated by a Door Control Transmitter Assembly, which sends radio waves to the Door Control & Tire Pressure Monitor Receiver Assembly. The Main Body ECU (Multiplex Network Body ECU) performs an ID code verification process and operates the door lock control.

FUNCTION OF MAIN COMPONENTS

Component

Function

Door Control Transmitter Assembly

  • Equipped with lock, unlock and hazard switches*1.
  • Transmits weak radio waves (ID codes and function codes) to the Door Control & Tire Pressure Monitor Receiver Assembly.

Door control receiver and tire pressure warning system receiver assembly.

Receives weak radio waves from the Door Control Transmitter Assembly and sends them to the Main Body ECU (Multiplex Network Body ECU).

  • Door Courtesy Light Switch Assembly
  • Luggage compartment door sill light switch
  • Lights when a door is opened and goes off when it is closed.
  • Sends door open/closed position signals to the main body ECU (multiplex network body ECU).

Unlock Warning Switch Assembly

Detects whether or not the key is inserted in the ignition switch.

Front Door Lock Assembly with Motor

Rear Door Lock Assembly with Motor

  • The built-in motor locks or unlocks the door.
  • Sends the lock position of each door to the main body ECU (multiplex network body ECU).

Main body ECU (multiplex network body ECU)

Sends remote door lock control signals in response to code data from the Door Control & Tire Pressure Monitor Receiver Assembly, as well as signals from each switch.

  • *1: with Toyota Safety Sense P system

SYSTEM OPERATION

The Door Control Transmitter Assembly has lock and unlock switches. Pressing these switches activates each function.

The wireless power door lock system has the following functions:

HINT:

The default settings of the following functions are ON. Some of these functions can be customized.

Click here

Function

Operation

Locking all doors

Press the lock switch to lock all doors.

Unlocking all doors

Press the unlock switch to unlock all doors.

Unlocking all doors

(2-Step Unlock)

Press the unlock switch twice within 5 seconds. The driver's door unlocks first, then all doors unlock.

Automatic Re-Lock

If no door is opened within 60 seconds after being unlocked by the remote power door lock control, all doors will automatically lock again.

Automatic Response (Hazard Lights)

  • When the doors are locked remotely, the hazard lights flash once.
  • When the doors are unlocked remotely, the hazard lights flash twice.

Automatic Response (Remote Door Lock Buzzer)*1

  • When the doors are locked by remote control, the remote door lock buzzer sounds once.
  • When the doors are unlocked by remote control, the remote door lock buzzer sounds twice.

Panic Alarm*1

Pressing and holding the panic switch on the Door Control Transmitter Assembly for approximately 0.8 seconds or more activates the following alarms:

  • Sounds the horn and vehicle alarm.
  • Flashes the headlights, tail lights and hazard lights.
  • Turns on the interior light.

While the panic alarm is operating, pressing any switch on the Door Control Transmitter Assembly cancels its operation.

Door Ajar Warning*1, *2

The buzzer sounds when the lock switch is pressed and any door is ajar, and it sounds continuously for 5 seconds. The buzzer stops when all doors are closed and the unlock switch is pressed.

Remote Lock Reservation*1, *2

Pressing the lock button on the Door Control Transmitter Assembly while a door is open causes that door to lock when it is closed.

Entry light

When all doors are locked, pressing the unlock switch turns on the interior light at the same time as the doors unlock.

Self-Diagnosis Mode

When the Door Control & Tire Pressure Monitor Receiver Assembly receives normal radio waves from the Door Control Transmitter Assembly while the system is in diagnostic mode, the interior light flashes in a normal sequence corresponding to the function of each switch.

Transmitter ID Code Registration

Allows registration (input and storage) of Door Control Transmitter Assembly ID codes in the EEPROM contained in the Door Control & Tire Pressure Monitor Receiver Assembly.

  • *1: with Toyota Safety Sense P system

HINT:

*2: If the customization setting "Wireless Lock Function with Doors Open" is set to ON, the "Door Ajar Warning" will no longer operate. If the "Door Ajar Warning" is set to ON, the "Wireless Lock Function with Doors Open" will no longer operate. If both settings are set to ON, priority is given to the "Wireless Lock Function with Doors Open".

TRANSMITTER ID CODE REGISTRATION FUNCTION

The table below shows the 4 ID registration modes. Codes are registered electronically (written and stored) in the EEPROM contained in the Door Control & Tire Pressure Monitor Receiver Assembly.

Mode

Function

Add Mode

Adds a new code while retaining previously registered codes.

This mode is used when adding a new Door Control Transmitter Assembly. If the maximum number of registrations is exceeded, the oldest code is deleted first.

Re-register Mode

Deletes all previously registered codes and registers only the newly entered codes.

Confirmation Mode

Confirms the number of registered codes. When adding a new code, this mode is used to check the number of codes already registered.

Prohibition Mode

Deletes all registered codes and disables the remote door lock function.

This mode is used when the Door Control Transmitter Assembly is lost.

CONDITIONS IN WHICH REMOTE FUNCTIONS DO NOT OPERATE

(a) The lock function does not operate when any of the following conditions is met:

  • One of the doors is open.
  • The key is inserted in the ignition switch.

(b) The unlock function does not operate when the following condition is met:

  • The key is inserted in the ignition switch.