Door Lock

Only the remote control function does not operate

~10min read

DESCRIPTION

The door control receiver and tire pressure warning system assembly receives the signals transmitted by the door control transmitter assembly and sends these signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then controls all doors by sending lock / unlock signals to each door, and sends the hazard light signals to the combination meter assembly.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Check the fuses for the circuits related to this system before performing the following procedure.
  • When replacing or inspecting the door control receiver and tire pressure warning system assembly or the wire harness, do not change the position or length of the wire harness. If the wire harness is routed too close to the door control receiver and tire pressure warning system assembly, the performance of the remote control function may be affected.
  • When replacing the door control receiver and tire pressure warning system assembly, use the Techstream to read the transmitter IDs stored in the old ECU and record them before removal.
  • Initialization is required after registering the transmitter IDs in the tire pressure warning ECU after replacing the ECU.

PROCEDURE

  1. CHECK POWER DOOR LOCK SYSTEM OPERATION

(a) Check the operation of the door lock central control.

Click here

OK:

Locked doors unlock

NG

GO TO DOOR LOCK CONTROL SYSTEM

OK
  1. KEY REMINDER WARNING SYSTEM INSPECTION

(a) Make sure the key reminder warning buzzer operates correctly.

Click here

OK:

The key reminder warning buzzer operates correctly.

NG

GO TO KEY REMINDER WARNING SYSTEM

OK
  1. CHECK DOOR CONTROL TRANSMITTER ASSEMBLY

(a) When a registered, good-condition door control transmitter assembly is used, make sure the remote control functions operate correctly.

Result:

Result

Proceed to

The remote door lock / unlock function operates correctly using a good-condition door control transmitter assembly.

A

The remote door lock does not operate.

B

B

GO TO STEP 5

A
  1. CHECK TRANSMITTER BATTERY (VOLTAGE)

(a) Check the battery capacity.

(1) Remove the battery from the malfunctioning door control transmitter assembly (see page ). Attach a conductive wire (0.6 mm (0.0236 in.) diameter maximum, including insulation) to the negative (-) terminal using adhesive tape or similar material.

NOTICE:

Do not wrap the conductive wire around a terminal, wedge it between terminals, or solder it. A terminal may be deformed or damaged, and the battery will not be installed correctly.

(b) Carefully pull the conductive wire out of the position shown in the diagram, and reinstall the previously removed transmitter battery.

NOTICE:

When replacing the transmitter battery, before starting work, discharge any static electricity built up in the body, for example by touching the vehicle, to prevent damage to the door control transmitter assembly.

(c) Check the voltage of the transmitter battery.

HINT:

Measure the transmitter battery voltage while pressing the lock or unlock switch of the door control transmitter assembly.

Standard voltage:

Item

Content

Tester Connection

Positive (+) terminal of transmitter battery - negative (-) terminal of transmitter battery

Condition

Ignition switch OFF, all doors closed and lock or unlock switch pressed

Specified Condition

2,5 à 3,2 V

OK

REPLACE DOOR CONTROL TRANSMITTER ASSEMBLY

NG

REPLACE TRANSMITTER BATTERY

  1. CHECK RADIO WAVE ENVIRONMENT

(a) Bring the door control transmitter assembly close to the door control receiver and tire pressure warning system assembly, and perform a remote control operation check.

HINT:

  • When the door control transmitter assembly is brought close to the door control receiver and tire pressure warning system assembly, the risk of radio wave interference decreases, and it is possible to determine whether interference is causing the symptom.
  • If the check shows that the problem occurs only in certain locations or at certain times of the day, the risk of radio wave interference may be high. In addition, adding parts to the vehicle may cause radio wave interference. If any parts have been added, remove them and perform the operation check again.

OK:

The remote control functions operate correctly.

OK

END (AFFECTED BY RADIO WAVE INTERFERENCE)

NG
  1. GO TO DIAGNOSIS MODE (USING TECHSTREAM)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menu items: Body Electrical / Main Body / Wireless Diagnosis Mode.

Body Electrical > Main Body > Utility

Wireless Code Registration

(e) Proceed to the next step as instructed on the Techstream screen.

(f) Check whether the system has entered self-diagnosis mode by checking the interior light display sequence.

NEXT
  1. CHECK DIAGNOSIS MODE

(a) Check the diagnostic transmission when the door control transmitter assembly switch is pressed. The diagnostic transmission can be checked using the interior light flashing patterns.

Result:

Result

Proceed to

A normal wave (flashing pattern) is transmitted.

A

A non-conforming recognition code is transmitted.

B

No diagnosis is transmitted.

C

A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

GO TO STEP 9

B
  1. CHECK RECOGNITION CODE REGISTRATION

(a) Make sure the system can enter re-registration mode or add mode, and that a recognition code can be registered.

Click here

OK:

The recognition code can be registered.

OK

END (GO TO OPERATION CHECK)

NG

GO TO STEP 13

  1. CHECK DOOR CONTROL RECEIVER AND TIRE PRESSURE WARNING SYSTEM ASSEMBLY (RESPONSE)

(a) Prepare the door control transmitter assembly from another vehicle.

(b) Press and hold the door control transmitter assembly switch.

(c) Check whether a non-conforming recognition code is transmitted.

OK:

A non-conforming recognition code is transmitted.

OK

REPLACE DOOR CONTROL TRANSMITTER ASSEMBLY (CUT KEY)

NG
  1. CHECK DOOR CONTROL RECEIVER AND TIRE PRESSURE WARNING SYSTEM ASSEMBLY (+B, GND)

(a) Disconnect connector M23 from the door control and tire pressure monitoring receiver assembly.

*a

Front view of wire harness side connector

(to door control receiver and tire pressure warning system assembly)

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

M23-12 (GND) - Body ground

Always

Below 1 Ω

(c) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

M23-7 (+B) - Body ground

Always

11 à 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK DOOR CONTROL RECEIVER AND TIRE PRESSURE WARNING SYSTEM ASSEMBLY (OUTPUT)

(a) Connect the door control receiver and tire pressure warning system assembly M23.

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

M23-4 (RDA) - Body Ground

Ignition Switch Lock, All Doors Closed and Door Control Transmitter Assembly Switch Not Pressed

11 à 14 V

Ignition Switch Lock, All Doors Closed and Door Control Transmitter Assembly Switch Pressed

Pulse generation

(0 à 12 V)

*a

Component with Wire Harness Connected

(Door Control Receiver & Tire Pressure Warning System Receiver Assembly)

NG

REPLACE DOOR CONTROL RECEIVER & TIRE PRESSURE WARNING SYSTEM RECEIVER ASSEMBLY

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - DOOR CONTROL RECEIVER & TIRE PRESSURE WARNING SYSTEM RECEIVER ASSEMBLY)

(a) Disconnect the F15 connector from the main body ECU (multiplex network body ECU).

(b) Disconnect the M23 connector from the Door Control Receiver & Tire Pressure Warning System Receiver Assembly.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

M23-4 (RDA) - F15-4 (RDA)

Always

Below 1 Ω

M23-5 (PRG) - F15-5 (PRG)

Always

Below 1 Ω

M23-4 (RDA) - Body Ground

Always

10 kΩ minimum

M23-5 (PRG) - Body Ground

Always

10 kΩ minimum

F15-4 (RDA) - Body ground

Always

10 kΩ minimum

F15-5 (PRG) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE DOOR CONTROL RECEIVER & TIRE PRESSURE WARNING SYSTEM RECEIVER ASSEMBLY

(a) Temporarily replace the Door Control Receiver & Tire Pressure Warning System Receiver Assembly with a new or known-good one.

Click here

NEXT
  1. CHECK RECOGNITION CODE REGISTRATION

(a) Perform the registration procedure.

Click here

NEXT
  1. INSPECT DOOR CONTROL RECEIVER & TIRE PRESSURE WARNING SYSTEM RECEIVER ASSEMBLY (OPERATION)

(a) Check whether the doors can be locked and unlocked using the lock and unlock switches on the Door Control Transmitter Assembly.

OK:

The doors can be locked and unlocked by the Door Control Transmitter Assembly.

OK

END (DOOR CONTROL RECEIVER & TIRE PRESSURE WARNING SYSTEM RECEIVER ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)