Door Lock

Operation Check

~6min read

OPERATION CHECK

NOTES ON THE FOLLOWING CHECKS

(a) Remote door lock/unlock function:

The remote door locking system only operates when the following 3 conditions are met:

(1) No key is in the ignition switch.

(2) All doors are closed.

(3) The central door locking system operates correctly.

HINT:

The unlock function operates even when a door is open.

(b) The size of the remote door locking operating range may vary depending on conditions.

(1) The size of the operating range depends on the user and on how the Door Control Transmitter Assembly is oriented.

(2) In some areas, the operating range of the remote door locking function may be limited by the shape of the vehicle body and by the influence of the surrounding environment.

(3) Because the Door Control Transmitter Assembly uses weak radio waves, strong radio waves or electrical noise in the frequency used by the Door Control Transmitter Assembly may reduce the operating range, and remote control may not function.

(4) When the transmitter battery is weak, the operating range decreases and the remote control may not work.

HINT:

Leaving the door control transmitter assembly in a location directly exposed to sunlight, such as on the instrument panel, for example, may cause the transmitter battery to weaken or other problems.

CHECK REMOTE DOOR LOCK FUNCTIONS

NOTICE:

The check procedure below assumes the vehicle has not been customized from its original configuration.

HINT:

  • The switches described in this text are switches that transmit signals. The switches are built into the door control transmitter assembly.
  • These functions must be checked against the operating range of the remote control.

(a) Make sure the vehicle is within an area where the remote control function can operate.

(b) Check the basic functions.

(1) Check that all doors lock when the lock switch is pressed.

(2) Check that all doors unlock when the unlock switch is pressed.

(c) Check the anti-repeat function.

(1) Check that the corresponding operation occurs only once and does not repeat continuously when the switch is held down. However, make sure the operation works correctly when the switch is pressed repeatedly at 1-second intervals.

(d) Check the auto lock function.

(1) Make sure that all doors automatically lock again if none of them has been opened, or if all doors are locked within approximately 60 seconds after unlocking the doors using the unlock switch.

(2) Make sure the auto lock function does not operate when a door has been opened within approximately 60 seconds after the doors are unlocked using the unlock switch.

(3) Make sure the auto lock function does not operate when all doors have been locked manually (such as with the key operation or by pressing the lock switch) within approximately 60 seconds after the doors are unlocked using the unlock switch.

(e) Check the switch security function.

(1) Make sure that the doors cannot be locked/unlocked by operating a switch on an unregistered door control transmitter assembly, but can be locked/unlocked by operating a switch on the registered door control transmitter assembly.

(2) Check that the doors cannot be locked/unlocked when a switch is operated and the key is in the key cylinder. This does not apply when registering the ID code.

(f) Check the repeat function.

(1) Check that all doors tend to relock automatically 1 second after the lock switch is pressed while the driver's door control switch is held in the unlock position.

(g) Check the automatic response function (hazard lights).

(1) Check that the hazard lights flash once at the same time as all doors lock when the lock switch is pressed.

(2) When the unlock switch is pressed once, make sure the hazard lights flash twice at the same time as all doors unlock.

(h) Check the automatic response function (remote door lock buzzer).*1

(1) When the lock switch is pressed, check that the buzzer sounds once at the same time as all doors unlock.

(2) When the unlock switch is pressed once, check that the buzzer sounds twice at the same time as all doors unlock.

(i) Check the remote door lock reservation function.*1, *2

(1) If the lock switch on the door control transmitter assembly is pressed while any door is ajar or open, all doors lock when the door is closed.

(j) Check the door ajar warning light function.*1, *2

(1) Check that the remote door lock buzzer sounds for approximately 5 seconds when the lock switch is pressed and any door is open or ajar.

(k) Make sure the door lock stop function works when a door is open/ajar.

(1) When a door is open or ajar, check that the doors cannot be locked when the lock switch is operated.

HINT:

The doors can be unlocked even when a door is open or ajar.

(l) Check the panic alarm control function.*1

(1) With the anti-theft alarm function, check that the buzzer sounds, the headlights and tail lights flash, and the interior light stays on (when the light switch is set to DOOR) for 60 seconds when the PANIC switch is held for at least 0.8 seconds. Also check that the buzzer stops sounding and the lights stop flashing when any transmitter switch is pressed.

(m) Check the door courtesy light function.

Click here

(n) Check the power window open/close function.

Click here

  • *1: with Toyota Safety Sense P system

HINT:

*2: If the customization setting "Wireless Lock Function with Doors Open" is set to ON, the "Door Ajar Warning" will no longer operate. If the "Door Ajar Warning" is set to ON, the "Wireless Lock Function with Doors Open" will no longer operate. If both settings are set to ON, priority is given to the "Wireless Lock Function with Doors Open".