Door Lock

Operation History

~16min read

OPERATION HISTORY

NOTICE:

  • If the vehicle or vehicle controls are operated (for example, during inspection when the vehicle is brought in for repairs) before the operation history is read and recorded, the operation history information may be lost.
  • The "Read Operation History" function uses the current system time setting in Techstream and the clock in the inspection ECU to calculate the times shown in the operation history. For this reason, before reading the operation history, first make sure the Techstream system clock is set accurately to the current time.
  • Door lock/unlock operation using the door lock button is not recorded in the operation history.
  • When the door is not fully closed, so that the door lock cannot be performed and the door ajar warning sounds, the operation is not recorded in the lock operation history.

Operation history

HINT:

Operation history: The main body ECU (multiplex network body ECU) (multiplex network body ECU) records the operation history of the power door lock system, which can be read using the Techstream.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menus: Body Electrical / Main Body / Utility / Operation History.

(e) Follow the on-screen instructions to record the operation history.

When I arrived at the vehicle, I found the doors unlocked.

Tester display

Item Description

Recorded Reason

Remarks

Manual Unlock

Unlock operation signal on the door control switch unlock side recognized by the main body ECU (multiplex network body ECU).

Unlock operation signal of the door control switch detected by the main body ECU (multiplex network body ECU).

  • The door control switch unlock operation has been performed.
  • Door control switch unlock side stuck
  • Door control switch unlock side activation malfunction (internal malfunction).
  • Short to ground in the wire harness between the door control switch unlock side and the main body ECU (multiplex network body ECU).
  • Main body ECU (multiplex network body ECU) malfunction (short to ground in the ECU internal circuit).

-

Door Key Linked Unlock

Unlock operation signal on the driver door key cylinder unlock side recognized by the main body ECU (multiplex network body ECU).

Unlock operation signal on the key cylinder unlock side detected by the main body ECU (multiplex network body ECU).

  • A key cylinder unlock side operation has been performed.
  • Key cylinder unlock side activation malfunction.
  • Short to ground in the wire harness between the key cylinder unlock side and the main body ECU (multiplex network body ECU).
  • Main body ECU (multiplex network body ECU) malfunction (short to ground in the ECU internal circuit).

-

Key Detected Unlock 1

  • With the IG ON or ACC ON position, and when the driver door is open, the lock operation signal of the driver door lock button is recognized by the main body ECU (multiplex network body ECU).
  • With the IG ON or ACC ON position, and when the front passenger door is open, the lock operation signal of the front passenger door lock button is recognized by the main body ECU (multiplex network body ECU).

A driver door lock button door lock operation signal is detected by the main body ECU (multiplex network body ECU).

  • With the IG ON or ACC ON position, and when the driver door is open, the lock operation of the driver door lock button is performed.
  • With the IG ON or ACC ON position, and when the front passenger door is open, the lock operation of the front passenger door lock button is performed.
  • Front door lock position switch activation malfunction.
  • Short to ground in the wire harness between the front door lock position switch and the main body ECU (multiplex network body ECU).
  • Main body ECU (multiplex network body ECU) malfunction (short to ground in the ECU internal circuit).
  • Door courtesy light switch circuit malfunction.
  • Power supply circuit malfunction.

-

Key Detected Unlock 2

With the IG ON or ACC ON position, and when the driver door is open, the lock operation signal of the door control switch or the driver door key cylinder is recognized by the main body ECU (multiplex network body ECU).

With the IG ON or ACC ON position, and when the driver door is open, the lock operation signal of the door control switch or the driver door key cylinder is detected by the main body ECU (multiplex network body ECU).

  • With the IG ON or ACC ON position, and when the driver door is open, the lock operation of the door control switch or the driver door key cylinder is performed.
  • When the door courtesy light switch is in the ON position, the door control switch has a lock side activation malfunction.
  • When the door courtesy light switch is in the ON position, there is a short to ground in the wire harness between the door control switch lock side and the main body ECU (multiplex network body ECU).
  • When the door courtesy light switch is in the ON position, the driver door key cylinder switch has a lock side activation malfunction.
  • Door courtesy light switch circuit malfunction.
  • Power supply circuit malfunction.

-

Key Detected Unlock 3

  • With the IG ON or ACC ON position, and when the driver door is open, the lock operation signal of the door control switch or the driver door key cylinder is recognized by the main body ECU (multiplex network body ECU).
  • With the IG ON or ACC ON position, and when the front passenger door is open, the lock operation signal of the door control switch or the front passenger door key cylinder is recognized by the main body ECU (multiplex network body ECU).

Driver's door closed signal detected by the main body ECU (multiplex network body ECU).

  • With the IG ON or ACC ON position, and when the driver door is open, the lock operation of the door control switch or the driver door key cylinder is performed.
  • In IG ON or ACC ON position, and when the front passenger door is open, the lock operation of the door control switch or front passenger door cylinder is performed.
  • Malfunction of the door courtesy light switch.
  • Power supply circuit malfunction.

-

Wireless Unlock

In IG OFF or ACC OFF position, a remote unlock request signal is recognized by the main body ECU (multiplex network body ECU).

Electronic key unlock signal detected by the main body ECU (multiplex network body ECU).

  • The electronic key unlock switch has been pressed.
  • The electronic key unlock switch has been pressed by something while inside a pocket, bag, etc.
  • Malfunction of the remote door central locking system.
  • Power supply circuit malfunction.

NOTICE:

The electronic key number* and the duration the unlock switch was continuously pressed are recorded.

*Only for systems that store the electronic key number.

Auto Entry Unlock*1

In IG OFF or ACC OFF position, an unlock-on-door-open request signal from any door is recognized by the main body ECU (multiplex network body ECU).

Unlock-on-door-open signal detected by the main body ECU (multiplex network body ECU).

  • The door handle unlock sensor has been touched.
  • Water splashed onto the door handle unlock sensor due to rain or car washing caused the sensor to react.
  • Malfunction in the smart key system circuit.
  • Power supply circuit malfunction.

-

Key in Vehicle Detected Unlock*1

Unlock-on-door-open request signal for all seats recognized by the main body ECU (multiplex network body ECU).

Unlock-on-door-open signal for the key confinement prevention function detected by the main body ECU (multiplex network body ECU).

  • With the electronic key transmitter sub-assembly inside the vehicle cabin, and with the lock position switches of all doors in the locked position, a door was opened and closed while pulling the door handle.
  • With the electronic key transmitter sub-assembly outside the vehicle cabin but with the certification evaluation inside the cabin correct, and with the lock position switches of all doors in the locked position, a door was opened and closed while pulling the door handle.

-

Door Unlock by Active Test

Door unlock using diagnostic tester (Active Test) recognized by the main body ECU (multiplex network body ECU).

The door has been unlocked using the diagnostic tester (Active Test).

On vehicles fitted with aftermarket components (automatic door locks), sometimes recorded when the doors are unlocked.

  • *1: with Smart Key System
The doors lock unintentionally (when the vehicle is stopped or when the vehicle is being driven).

Tester display

Item Description

Recorded Reason

Remarks

Manual Lock

Lock side operation signal of the door control switch recognized by the main body ECU (multiplex network body ECU).

Door control switch lock operation signal detected by the main body ECU (multiplex network body ECU).

  • The lock operation of the door control switch has been performed.
  • Lock side sticking of the door control switch
  • Malfunction in lock side activation of the door control switch (internal malfunction).
  • Short to ground in the wire harness between the lock side of the door control switch and the main body ECU (multiplex network body ECU).
  • Main body ECU (multiplex network body ECU) malfunction (short to ground in the ECU internal circuit).

-

Door Key Linked Lock

Lock side operation signal of the driver's door lock cylinder recognized by the main body ECU (multiplex network body ECU).

Lock side operation signal of the driver's door lock cylinder detected by the main body ECU (multiplex network body ECU).

  • A lock side operation of the lock cylinder has been performed.
  • Malfunction in lock side activation of the lock cylinder.
  • Short to ground in the wire harness between the lock side of the cylinder and the main body ECU (multiplex network body ECU).
  • Main body ECU (multiplex network body ECU) malfunction (short to ground in the ECU internal circuit).

-

Wireless Lock

In IG OFF position and with all doors closed, a remote lock request signal is recognized by the main body ECU (multiplex network body ECU).

In IG OFF position and with all doors closed, a remote lock request signal is detected by the main body ECU (multiplex network body ECU).

  • The electronic key lock switch has been pressed.
  • The electronic key lock switch has been pressed by something while inside a pocket, bag, etc.
  • Malfunction of the remote door central locking system.
  • Power supply circuit malfunction.

NOTICE:

The electronic key number* and the duration for which the lock switch was continuously pressed are recorded.

*Only for systems that store the electronic key number.

Wireless Auto Lock (30s)

After the remote unlock operation, IG ON or ACC ON mode was not activated, or none of the doors were opened or closed within a set time, and this is recognized by the main body ECU (multiplex network body ECU).

*: The specified time can be changed using the customization settings.

After the electronic key unlock operation, IG ON or ACC ON mode was not activated or the doors were not opened within a set time, and this is detected by the main body ECU (multiplex network body ECU).

  • The remote unlock switch has been pressed.
  • The remote unlock switch was pressed by something while it was inside a pocket, bag, etc.
  • Malfunction of the remote door central locking system.
  • Power supply circuit malfunction.

-

Auto Entry Lock*1

With the IG OFF position and all doors closed, the main body ECU (multiplex network body ECU) detects a lock request signal when one of the doors is opened.

  • The door handle lock sensor was touched.
  • Water splashed onto the door handle lock sensor due to rain or car washing caused the sensor to react.
  • Malfunction in the smart key system circuit.
  • Power supply circuit malfunction.

-

Auto Entry Lock (30s)*1

After the unlock-on-approach operation, IG ON or ACC ON mode was not activated, or none of the doors were opened or closed within the specified time. This is detected by the main body ECU (multiplex network body ECU).

*: The specified time can be changed using the customization settings.

After the unlock-on-approach operation, IG ON or ACC ON mode was not activated, or the doors were not opened within the specified time. This is detected by the main body ECU (multiplex network body ECU).

  • The door handle unlock sensor has been touched.
  • Malfunction in the smart key system circuit.
  • Door courtesy light switch circuit malfunction.
  • Power supply circuit malfunction.

-

Security Forced Lock

When the automatic alarm sounds, the main body ECU (multiplex network body ECU) detects that one of the doors has been unlocked by a method other* than remote unlock, unlock-on-approach, or the mechanical key.

*: Only when the function is available.

When the automatic alarm sounds, the main body ECU (multiplex network body ECU) detects that one of the doors is in the unlocked position.

  • When the automatic alarm sounds, one of the doors has been unlocked by a method other* than remote unlock, unlock-on-approach, or the mechanical key.
  • Malfunction in the automatic alarm circuit (automatic alarm system).
  • Malfunction in the door lock position circuit.

*: Only when the function is available.

-

Door Lock by Active Test

Door locked using the diagnostic tester (Active Test) and detected by the main body ECU (multiplex network body ECU).

The door was locked using the diagnostic tester (Active Test).

On vehicles equipped with aftermarket components (automatic door locks), sometimes recorded when the doors are locked.

  • *1: with Smart Key System

HINT:

Explanation of Operation History Display Items.

Item

Description

Time Information

Time during which the main body ECU (multiplex network body ECU) performed each operation history item.

Ignition ON/OFF Counter

  • The counter increases when the ignition switch is turned from ON to OFF.
  • The initial value is 0 times, the maximum value is 255 times.
  • When the value reaches 255, it returns to 0 at the next increment and counting continues.

Operation Details

Name of the operation history item performed by the main body ECU (multiplex network body ECU).

Elapsed time since CPU reset

Starting from the moment battery supply voltage to the main body ECU (multiplex network body ECU) began, the elapsed time until each operation history item was performed.

Number of CPU resets

  • Number of times battery supply voltage to the main body ECU (multiplex network body ECU) changed from an unpowered* state to a powered state.
  • The initial value is 0 times. The maximum value is 3 times.
  • When the value reaches 3, it returns to 0 at the next increase, and counting continues.

*: Operation history resulting in an unpowered state includes battery removal/installation, main body ECU (multiplex network body ECU) removal/installation, battery voltage drop, etc.