Door Lock

Operation Check

~8min read

OPERATION CHECK

CHECK POWER DOOR LOCK SYSTEM OPERATION

NOTICE:

The check procedure below assumes the vehicle has not been customized from its original configuration.

(a) Check basic functions.

(1) Make sure all doors lock when the lock side of the door control switch is pressed.

(2) Make sure all doors unlock when the unlock side of the door control switch is pressed.

(3) Make sure all doors lock when the driver's door lock cylinder is turned to the lock position using the mechanical key.

(4) Make sure only the driver's door unlocks when the driver's door lock cylinder is turned to the unlock position using the key, and that all doors unlock when it is turned to the unlock position again.

(b) Check the key lock-out prevention function (with smart key system).

NOTICE:

To prevent the key from being locked inside the vehicle, perform the following check with the driver's door window open.

(1) Set the ignition switch to ON or ACC.

(2) With the driver's door open, check that all doors unlock immediately when the driver's door lock button is pressed.

(3) With the driver's door open, check that all doors unlock immediately when the lock side of the door control switch is pressed.

(4) With the driver's door open, press and hold the driver's door lock button for at least 2 seconds, then close the driver's door and make sure all doors unlock.

(c) Check the key lock-out prevention function (without smart key system).

NOTICE:

To prevent the key from being locked inside, perform the following check with the driver's door window open.

(1) Insert the key into the ignition key cylinder.

(2) With the driver's door open, make sure all doors unlock immediately when the driver's door lock button is set to LOCK.

(3) With the driver's door open, make sure all doors unlock immediately when the door control switch (for manual operation) is set to the lock position.

(4) With the driver's door open, press and hold the driver's door lock button for at least 2 seconds, then close the driver's door and make sure all doors unlock.

(d) Check the safety function of the power door lock system.

(1) Close all doors and leave the driver's door window open, so that the door control switch can be operated from outside the vehicle. (Step 1)

(2) Open the driver's door and remove the key from the vehicle. With the door still open, lock the door using the lock button. Hold the driver's door outside handle, open and close the door while holding the handle open (make sure the lock button remains in the locked position). Then, make sure the doors do not unlock when the unlock side of the door control switch is pressed from outside the vehicle.

(3) Starting from Step 1, with the key outside the vehicle, close and lock the driver's door using the mechanical key. Then, make sure the doors do not unlock when the unlock side of the door control switch is pressed from outside the vehicle.

(4) Starting from Step 1, with the key outside the vehicle, close and lock the driver's door using the remote door lock operation or the lock-on-open operation. Then, make sure the doors do not unlock when the unlock side of the door control switch is pressed from outside the vehicle.

HINT:

Check whether the safety function of the power door lock system is cancelled under the following conditions:

  • The ignition switch is in the ON (IG) position.*1
  • The engine is running.*2
  • The driver's door is unlocked using the key.
  • The unlock side of the door control switch is pressed after the door lock button has been unlocked manually.
  • The doors are unlocked by the remote control.*2
  • The doors are unlocked by the unlock-on-open operation.*1
  • *1: with Smart Key System
  • *2: Without smart key system

(e) Check the 2-step unlock function linked to the key.

HINT:

The 2-step unlock function linked to the key can be customized. Make sure this function is set to ON before performing this procedure.

Click here

(1) Lock all doors.

(2) Make sure only the driver's door unlocks when the driver's door lock cylinder is turned to the unlock position using the key, and that all doors unlock when it is turned to the unlock position again.

(f) Check the driver's side key-linked lock/unlock cancel function. (except Toyota Safety Sense P)

(1) With the ignition switch in the ON position and the driver's seat belt fastened, make sure the door lock/unlock functions do not operate when the driver's side key-linked door function is performed from outside the vehicle.

(g) Check the illumination function.

(1) Set the reading light switch to the DOOR position.

(2) With all doors locked, check that all doors unlock when the driver's door lock cylinder is turned to the unlock position using the key, and that the reading light comes on.

CHECK DOUBLE LOCK FUNCTION (except Toyota Safety Sense P)

NOTICE:

  • Never activate the double lock function when a person is inside the vehicle, as the doors cannot be opened from the inside. If the doors are locked accidentally, unlock the door using the remote unlock operation or the unlock-on-open operation*1.
    • *1: with Smart Key System
  • The double lock function does not apply to the luggage compartment door (back door).

(a) Make sure the double lock function is set using the remote door lock operation.

(1) Open all windows.

(2) Turn the ignition switch OFF.

(3) Open and close the driver's door and make sure all doors and the back door are properly closed.

(4) Press the lock switch on the door control transmitter*1 or the electronic key transmitter*2 twice within 5 seconds and make sure the hazard lights flash once as an automatic response.

  • *1: without smart key system
  • *2: with Smart Key System

(5) Try to unlock all doors using the vehicle's interior handle and make sure that no doors unlock.

(b) Make sure the double lock function is set using the lock-on-open operation (with smart key system).

(1) Open all windows.

(2) Turn the ignition switch OFF.

(3) Open and close the driver's door and make sure all doors and the back door are properly closed.

(4) Touch the lock sensor on the door outside handle twice while holding the electronic key transmitter sub-assembly within 5 seconds and check that the hazard lights flash once as an automatic response.

(5) Try to unlock all doors using the vehicle's interior handle and make sure that no doors unlock.

(c) Make sure the double lock function is cancelled.

(1) Unlock the door using the remote unlock operation or the unlock-on-open operation*1 while the double lock function is set, and make sure the hazard lights flash twice as an automatic response.

  • *1: with Smart Key System

(2) Make sure the doors can be opened from both the inside handle and the outside handle.

HINT:

If the transmitter battery is discharged, only the driver's door can be opened using the key. However, the anti-theft system remains armed. When the door is opened without using the electronic key transmitter sub-assembly, the anti-theft system alarm sounds.