Seat Belt

Disposal

~16min read
4special tools
0204060801004231N·mlb·ft
Tightening torque found on this page

DISPOSAL

PRECAUTION / NOTICE / HINT

CAUTION:

Before disposing of any SRS component, read and carefully follow all environmental and hazardous material regulations. Deployment before disposal may be considered a hazardous material treatment.

PROCEDURE

1. PRECAUTIONS

CAUTION:

  • Wear gloves and protective goggles when handling a front seat belt outer belt assembly whose pretensioner has deployed.
  • Always wash your hands with water after completing the work.
  • Do not pour water or any other liquid onto a front seat belt outer belt assembly whose pretensioner has deployed.
  • Always use the specified SST for deploying the seat belt pretensioner (SRS airbag deployment tool). Perform this operation in a location free of electrical noise.
  • Never dispose of a front seat belt outer belt assembly whose pretensioner has not deployed.
  • The front seat belt outer belt assembly makes an explosive noise when the pretensioner deploys. Therefore, perform this operation outside, in a place where it will not disturb residents.
  • When deploying the seat belt pretensioner, perform the operation at least 10 m (32.8 ft) away from the vehicle.

HINT:

Before scrapping a vehicle equipped with a seat belt pretensioner, or disposing of a front seat belt outer belt assembly with a seat belt pretensioner, always deploy the seat belt pretensioner first in accordance with the procedure described below. If any abnormality occurs while deploying the seat belt pretensioner, immediately contact the Service and Repair department of TOYOTA MOTOR SALES, U.S.A., INC.

2. DISPOSE OF FRONT SEAT BELT OUTER BELT ASSEMBLY (when installed on vehicle)

NOTICE:

  • When disposing of a front seat belt outer belt assembly with pretensioner, never deploy the pretensioner inside the customer's vehicle.
  • Be sure to follow the procedure below when deploying a seat belt pretensioner.

HINT:

Prepare a battery to be used as the power supply for deploying the seat belt pretensioner.

(a) Check that the SST operates correctly.

SST: 09082-00700

CAUTION:

Always use the specified SST when deploying a seat belt pretensioner.

(1) Connect the red SST clip to the battery positive (+) terminal, and the black SST clip to the battery negative (-) terminal.

HINT:

At this stage, do not connect the yellow connector. It will be connected to the seat belt pretensioner later.

*a

Battery

(2) Press the SST activation switch and check that the LED on the switch lights up.

CAUTION:

If the LED lights up when the special service tool activation switch is pressed, the special service tool may be malfunctioning. In this case, do not use the malfunctioning SST.

(b) Refer to the Precautions.

Click here

(c) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(d) Remove the center pillar lower garnish.

Click here

(e) Disconnect the seat belt pretensioner connector.

(f) Using a screwdriver with its tip wrapped in protective tape, pry out the lock button to release the lock and disconnect the pretensioner connector as shown in the illustration.

*a

Lock button

*b

Protective tape

(g) Using a screwdriver with its tip wrapped in protective tape, pry out the lock button to release the lock and disconnect the force limiter connector as shown in the illustration. (for front passenger seat belt with select force limiter)

*a

Lock button

*b

Protective tape

(h) Reinstall the bolt on the lower part of the retractor.

Torque:

42 N·m {428 kgf·cm, 31 ft·lbf}

(i) Connect the SST.

(1) After connecting the following SSTs to each other, connect them to the seat belt pretensioner.

SST: 09082-00700

SST: 09082-00802

09082-10801

09082-20801

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the pretensioner connector.

(2) Move the SST at least 10 m (32.8 ft) away from the front of the vehicle.

*a

Battery

*b

10 m (32.8 ft) minimum

CAUTION:

  • Do not perform deployment with any door or window open.
  • If deployment is performed with any window or door open, dust or gas may come into contact with the eyes or be inhaled.

(3) Close all doors and windows of the vehicle.

NOTICE:

Be careful not to damage the SST wire harness.

(j) Deploy the seat belt pretensioner.

(1) Make sure that no one is in the vehicle or within a 10 m (32.8 ft) radius of the vehicle.

(2) Connect the red SST clip to the battery positive (+) terminal and the black SST clip to the battery negative (-) terminal.

(3) Press the SST activation switch to deploy the seat belt pretensioner.

HINT:

The seat belt pretensioner deploys when the SST LED lights up.

CAUTION:

  • The front seat belt outer belt assembly makes an explosive noise when the pretensioner deploys. Therefore, perform this operation outside, in a place where it will not disturb residents.
  • If this procedure is performed indoors or on a poor road where safety cannot be ensured, there is a risk of injury. Also, if this procedure is performed near a residential area, the deployment noise may disturb residents.

(4) Disconnect the SST.

(k) Connect the SST.

(1) After connecting the following SSTs to each other, connect them to the select force limiter.

SST: 09082-00700

SST: 09082-00802

09082-10801

09082-20801

NOTICE:

To avoid damaging the wire harness or the SST connector, do not activate the secondary lock of the select force limiter connector.

(2) Move the SST at least 10 m (32.8 ft) away from the front of the vehicle.

*a

Battery

*b

10 m (32.8 ft) minimum

CAUTION:

  • Do not perform deployment with any door or window open.
  • If deployment is performed with any window or door open, dust or gas may come into contact with the eyes or be inhaled.

(3) Close all doors and windows of the vehicle.

NOTICE:

Be careful not to damage the SST wire harness.

(l) Deploy the select seat belt force limiter.

(1) Make sure that no one is in the vehicle or within a 10 m (32.8 ft) radius of the vehicle.

(2) Connect the red SST clip to the battery positive (+) terminal and the black SST clip to the battery negative (-) terminal.

(3) Press the SST activation switch to deploy the select seat belt force limiter.

HINT:

The seat belt force limiter deploys at the same time the SST LED lights up.

CAUTION:

  • The front seat belt outer belt assembly makes an explosive noise when the select force limiter deploys. Therefore, perform this operation outside, in a place where it will not disturb residents.
  • If this procedure is performed indoors or on a poor road where safety cannot be ensured, there is a risk of injury. Also, if this procedure is performed near a residential area, the deployment noise may disturb residents.

(m) Dispose of the front seat belt outer belt assembly.

(1) Remove the front seat belt outer belt assembly and SST.

(2) Place the front seat belt outer belt assembly in a plastic bag, seal the bag securely, and dispose of it in accordance with applicable regulations.

CAUTION:

  • The front seat belt outer belt assembly becomes very hot when the pretensioner deploys. Wait at least 30 minutes after deployment before touching it.
  • Do not pour water or any other liquid onto a front seat belt outer belt assembly whose pretensioner has deployed.
  • If water is applied to the front seat belt outer belt assembly immediately after deployment, the steam may cause burns.
  • Always wear gloves and protective goggles when handling a front seat belt outer belt assembly whose pretensioner has deployed.
  • If a front seat belt outer belt assembly whose pretensioner has deployed is touched without wearing gloves and protective goggles, the hot parts may cause burns and dust may get into the eyes.
  • After removal, immediately seal the front seat belt outer belt assembly in a plastic bag.
  • Never dispose of a front seat belt outer belt assembly whose pretensioner has not deployed.
  • If a front seat belt outer belt assembly whose pretensioner has not deployed is disposed of and then deploys accidentally, unexpected injury may result.
  • Always wash your hands with water after completing the work.

HINT:

When scrapping a vehicle, deploy the seat belt pretensioners, then scrap the vehicle with the front outer seat belt assemblies installed.

3. DISPOSE OF FRONT SEAT BELT OUTER BELT ASSEMBLY (when not installed on vehicle)

NOTICE:

  • When disposing of a front seat belt outer belt assembly with pretensioner, never deploy the pretensioner inside the customer's vehicle.
  • Be sure to follow the procedure below when deploying a seat belt pretensioner.

HINT:

Prepare a battery to be used as the power supply for deploying the seat belt pretensioner.

(a) Check that the SST operates correctly.

SST: 09082-00700

CAUTION:

Always use the specified SST when deploying a seat belt pretensioner.

(1) Connect the red SST clip to the battery positive (+) terminal, and the black SST clip to the battery negative (-) terminal.

HINT:

At this stage, do not connect the yellow connector. It will be connected to the seat belt pretensioner later.

*a

Battery

(2) Press the SST activation switch and check that the LED on the switch lights up.

CAUTION:

If the LED lights up when the special service tool activation switch is pressed, the special service tool may be malfunctioning. In this case, do not use the malfunctioning SST.

(b) Refer to the Precautions.

Click here

(c) Remove the front seat belt outer belt assembly.

Click here

(d) Retract the seat belt webbing using the retractor.

*a

Cut

*b

100 mm (3.94 in)

(e) When the seat belt webbing is sufficiently retracted, cut it approximately 100 mm (3.94 in.) from the retractor, as shown in the illustration.

HINT:

The retractor resistance increases in proportion to the length of seat belt webbing wound.

(f) Connect the SST.

(1) After connecting the following SSTs to each other, connect them to the seat belt pretensioner.

SST: 09082-00700

SST: 09082-00802

09082-10801

09082-20801

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the pretensioner connector.

(2) Place the front seat belt outer belt assembly on the floor and cover it with an unused tire and wheel assembly.

NOTICE:

  • Place the front seat belt outer belt assembly as shown in the illustration.
  • The wheel and tire assembly may be damaged by the deployment of the seat belt pretensioner. Therefore, be sure to use an unused wheel and tire assembly.

(3) Place the SST and keep it at least 10 m (32.8 ft) away from the wheel and tire assembly.

NOTICE:

Be careful not to damage the SST wire harness.

(g) Deploy the seat belt pretensioner.

*a

Battery

*b

10 m (32.8 ft) minimum

(1) Make sure that no one is within a 10 m (32.8 ft) radius of the wheel and tire assembly.

(2) Connect the red SST clip to the battery positive (+) terminal and the black SST clip to the battery negative (-) terminal.

(3) Press the SST activation switch to deploy the seat belt pretensioner.

HINT:

The seat belt pretensioner deploys when the SST LED lights up.

CAUTION:

  • The front seat belt outer belt assembly makes an explosive noise when the pretensioner deploys. Therefore, perform this operation outside, in a place where it will not disturb residents.
  • If this procedure is performed indoors or on a poor road where safety cannot be ensured, there is a risk of injury. Also, if this procedure is performed near a residential area, the deployment noise may disturb residents.

(4) Disconnect the SST.

(h) Connect the SST.

(1) After connecting the following SSTs to each other, connect them to the select seat belt force limiter.

SST: 09082-00700

SST: 09082-00802

09082-10801

09082-20801

NOTICE:

To avoid damaging the wire harness or the SST connector, do not activate the secondary lock of the select force limiter connector.

(2) Place the front seat belt outer belt assembly on the floor and cover it with an unused tire and wheel assembly.

NOTICE:

  • Place the front seat belt outer belt assembly as shown in the illustration.
  • The tire and wheel assembly may be damaged by the deployment of the seat belt selectable force limiter. Therefore, be sure to use an unused tire and wheel assembly.

(3) Place the SST and keep it at least 10 m (32.8 ft) away from the wheel and tire assembly.

NOTICE:

Be careful not to damage the SST wire harness.

(i) Deploy the seat belt selectable force limiter. (for front passenger seat belt with selectable force limiter)

*a

Battery

*b

10 m (32.8 ft) minimum

(1) Make sure that no one is within a 10 m (32.8 ft) radius of the wheel and tire assembly.

(2) Connect the red SST clip to the battery positive (+) terminal and the black SST clip to the battery negative (-) terminal.

(3) Press the SST activation switch to deploy the select seat belt force limiter.

HINT:

The seat belt force limiter deploys at the same time the SST LED lights up.

CAUTION:

  • The front seat belt outer belt assembly makes an explosive noise when the select force limiter deploys. Therefore, perform this operation outside, in a place where it will not disturb residents.
  • If this procedure is performed indoors or on a poor road where safety cannot be ensured, there is a risk of injury. Also, if this procedure is performed near a residential area, the deployment noise may disturb residents.

(4) Disconnect the SST.

(j) Discard the front seat belt outer belt assembly.

(1) Remove the wheel and tire assembly and the SST.

(2) Place the front seat belt outer belt assembly in a plastic bag, seal the bag securely, and dispose of it in accordance with applicable regulations.

CAUTION:

  • The front seat belt outer belt assembly becomes very hot when the pretensioner deploys. Wait at least 30 minutes after deployment before touching it.
  • Do not pour water or any other liquid onto a front seat belt outer belt assembly whose pretensioner has deployed.
  • If water is applied to the front seat belt outer belt assembly immediately after deployment, the steam may cause burns.
  • Always wear gloves and protective goggles when handling a front seat belt outer belt assembly whose pretensioner has deployed.
  • If a front seat belt outer belt assembly whose pretensioner has deployed is touched without wearing gloves and protective goggles, the hot parts may cause burns and dust may get into the eyes.
  • After removal, immediately seal the front seat belt outer belt assembly in a plastic bag.
  • Never dispose of a front seat belt outer belt assembly whose pretensioner has not deployed.
  • If a front seat belt outer belt assembly whose pretensioner has not deployed is disposed of and then deploys accidentally, unexpected injury may result.
  • Always wash your hands with water after completing the work.