Replacement
REPLACEMENT
PRECAUTION / NOTICE / HINT
CAUTION:
- Prolonged and repeated contact of the skin with engine oil removes the natural oils from the skin, causing dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful substances that may cause skin cancer.
- Wear protective clothing and gloves. Avoid contact with used oil. In case of contact, thoroughly wash the skin with soap or a waterless hand cleaner. Never use gasoline, thinners or solvents to clean the skin.
- To protect the environment, used oil and oil filters must be disposed of only at designated disposal sites.
PROCEDURE
1. REMOVE NO. 4 ENGINE CENTER UNDER COVER
(a) Remove the 4 screws and the No. 4 engine center under cover. |
![]() |
2. DRAIN ENGINE OIL
(a) Remove the oil filler cap sub-assembly.
(b) Remove the oil drain plug and gasket, and drain the engine oil into a container.
(c) Clean the oil drain plug.
(d) Install a new gasket on the oil drain plug.
(e) Reinstall the oil drain plug.
Torque:
37 N·m {377 kgf·cm, 27 ft·lbf}
3. REMOVE OIL FILTER
(a) for oil filter sub-assembly type:
(1) Using the SST, remove the oil filter sub-assembly.
SST: 09228-06502
(b) for oil filter element kit type:
(1) Using the SST, loosen the oil filter cap sub-assembly 4 turns, align the cap tabs vertically, and drain the remaining engine oil from the oil filter cap sub-assembly. SST: 09228-06502 NOTICE: Do not remove the oil filter bracket clip when removing the oil filter cap sub-assembly. HINT: Place a container under the oil filter cap sub-assembly before loosening it. |
|
(2) Remove the oil filter cap sub-assembly.
(3) Remove the oil filter element and O-ring from the oil filter cap sub-assembly. NOTICE: Do not use any tools to remove the O-ring, to avoid damaging the oil filter cap sub-assembly. Be sure to remove it by hand. |
|
4. INSTALL OIL FILTER
(a) for oil filter sub-assembly type:
(1) Check and clean the oil filter sub-assembly mounting surface.
(2) Apply clean engine oil to the gasket of the new oil filter sub-assembly.
(3) Lightly screw in the oil filter sub-assembly by hand. Tighten until the gasket contacts the seat.
(4) Using the SST, tighten the oil filter sub-assembly.
SST: 09228-06502
Depending on the available workspace, select one of the following procedures:- If sufficient space is available, use a torque wrench to tighten the oil filter sub-assembly.
Torque:
17.5 N·m {178 kgf·cm, 13 ft·lbf}
- Otherwise, tighten the oil filter sub-assembly 3/4 turn by hand or with a regular wrench.
(b) for oil filter element kit type:
(1) Clean the inside of the oil filter cap sub-assembly, the threads and the O-ring groove.
(2) Apply a thin coat of engine oil to a new O-ring and install it on the oil filter cap sub-assembly. NOTICE:
|
|
(3) Install a new oil filter element into the oil filter cap sub-assembly.
(4) Remove dirt and foreign matter from the engine mounting surface.
(5) Apply a thin coat of engine oil again to the O-ring of the oil filter cap sub-assembly. Align the cutout of the oil filter cap sub-assembly threads at 90° with the grooves of the oil filter bracket, and temporarily tighten the oil filter cap sub-assembly. NOTICE: Make sure the O-ring is not caught between parts. |
![]() |
(6) Using the SST, tighten the oil filter cap sub-assembly. SST: 09228-06502 Torque: 25 N·m {255 kgf·cm, 18 ft·lbf} NOTICE:
|
|
5. ADD ENGINE OIL
(a) Add new engine oil and reinstall the oil filler cap sub-assembly.
Standard oil grade (without fuel vapor absorber pump module):Oil grade | Oil viscosity (SAE) |
|---|---|
API SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil |
|
API SL, SM or SN multigrade engine oil |
|
Oil grade | Oil viscosity (SAE) |
|---|---|
ILSAC GF-5 multigrade engine oil |
|
Item | Standard condition |
|---|---|
Oil drain and refill with oil filter replacement |
4.2 liters (4.4 US qts, 3.7 Imp. qts) |
Oil drain and refill without oil filter replacement |
3.9 liters (4.1 US qts, 3.4 Imp. qts) |
Dry fill |
4.7 liters (5.0 US qts, 4.1 Imp. qts) |
6. CHECK FOR ENGINE OIL LEAKS
(a) Start the engine. Make sure there are no engine oil leaks in the areas where work was performed.
7. CHECK ENGINE OIL LEVEL
Click here![]()
8. REINSTALL NO. 4 ENGINE CENTER UNDER COVER
(a) Reinstall the No. 4 engine center under cover using the 4 bolts.





