Toyota Camry Quiz
Automatic transmission / trans

Park/neutral position switch assy (ATM)

In this manual: Automatic transmission / trans
Introduction — 61Audio & visual system — 16Automatic transmission / trans — 19Transmission revolution (ATM) — 1Shift lock system (ATM) — 1Brake — 20Clutch — 10Communication system — 4Cooling — 15Cruise control — 3Drive shaft / propeller shaft — 9Emission control — 8Engine control system — 12Engine hood/door — 7Exhaust — 3Exterior/interior trim — 14Front suspension — 9Fuel — 12Heater & air conditioner — 16Ignition — 8Instrument panel/meter — 7Intake — 7Lighting — 11Lubrication — 16Manual transmission/transaxle — 13Parking brake — 10Power steering — 7Rear suspension — 10Seat — 12Service specifications — 26Sliding roof/convertible — 4Starting & charging — 11Starting system (2AZ−FE)(From July, 2003) — 1Starting system (1MZ−FE/3MZ−FE) — 1Steering column — 6Theft deterrent & door lock — 9Tire & wheel — 4Windshield/windowglass/mirror — 5Back window glass — 1Power window control system — 1Power mirror control system — 1Inner rear view mirror assy — 1Windshield glass — 1Wiring — 1
37steps
~222min
4/5difficulty
010203040506.95N·mlb·ft
Tightening torque found on this page
Done 0 of 37
REPLACEMENT
  1. REMOVE BATTERY
  2. REMOVE ENGINE COVER SUB−ASSY No.1
  3. REMOVE AIR CLEANER ASSY
  4. REMOVE AIR CLEANER HOSE No.1
  5. REMOVE INTAKE AIR RESONATOR SUB−ASSY
  6. REMOVE ENGINE UNDER COVER LH
  7. DISCONNECT TRANSMISSION CONTROL CABLE ASSY
  8. Remove the nut from the control shaft lever.
  9. Disconnect the control cable from the control shaft lever.
  10. Remove the clip and disconnect the control cable from the control cable bracket.
    8. REMOVE PARK/NEUTRAL POSITION SWITCH ASSY
8. REMOVE PARK/NEUTRAL POSITION SWITCH ASSY
  1. Disconnect the park/neutral position switch connector.
  2. Remove the nut, washer and control shaft lever.
  3. Pry out the lock plate.
  4. Remove the lock nut and lock plate.
  5. Remove the 2 bolts and pull out the park/neutral position switch.
    9. INSTALL PARK/NEUTRAL POSITION SWITCH ASSY
9. INSTALL PARK/NEUTRAL POSITION SWITCH ASSY
  1. Install the park/neutral position switch to the manual valve shaft.
  2. Temporarily install the 2 bolts.
  3. Place a new lock plate and tighten the nut. Torque: 6,9 N·m
  4. Temporarily install the control shaft lever.
  5. Turn the lever counterclockwise until it stops, then turn it clockwise 2 notches.
  6. Remove the control shaft lever.
  7. Align the groove with neutral basic line.
  8. Hold the switch in position and tighten the 2 bolts. Torque: 5,4 N·m
  9. Using a screwdriver, stake the nut with the lock plate.
  10. Install the control shaft lever, washer and nut. Torque: 12,7 N·m
  11. Connect the park/neutral position switch connector.
    10. INSTALL TRANSMISSION CONTROL CABLE ASSY
10. INSTALL TRANSMISSION CONTROL CABLE ASSY
  1. Install the control cable and a new clip to the bracket.
  2. Temporarily install the control cable to the control shaft lever with the nut.
  3. ADJUST SHIFT LEVER POSITION
  4. INSPECT SHIFT LEVER POSITION
  5. INSPECT PARK/NEUTRAL POSITION SWITCH ASSY
  6. INSTALL ENGINE UNDER COVER LH
  7. INSTALL INTAKE AIR RESONATOR SUB−ASSY
  8. INSTALL AIR CLEANER HOSE No.1
  9. INSTALL AIR CLEANER ASSY
  10. INSTALL ENGINE COVER SUB−ASSY No.1
  11. INSTALL BATTERY

Test yourself

A quick Toyota Camry quiz: every answer comes with an explanation and a link to the manual page.