Toyota Tacoma Quiz
Brake Control / Dynamic Control Systems

IG Supply Voltage Low (C120B)

In this manual: Brake Control / Dynamic Control Systems
Introduction — 15Maintenance — 8Audio / Video — 94Garage Door Opener — 7Navigation / Multi Info Display — 84Park Assist / Monitoring — 86Brake — 50Brake Control / Dynamic Control Systems — 165Parking Brake — 52gr-fks Charging — 252gr-fks Cooling — 212gr-fks Emission Control — 132gr-fks Engine Control — 322gr-fks Engine Mechanical — 332gr-fks Exhaust — 92gr-fks Fuel — 422gr-fks Ignition — 62gr-fks Intake — 72gr-fks Lubrication — 152gr-fks Starting — 38Ac60e Automatic Transmission / Transaxle — 146Axle — 19Clutch — 20Cruise Control — 168Differential — 50Drive Shaft — 6Propeller Shaft — 23Rc62f Manual Transmission / Transaxle — 34Suspension — 22Tire And Wheel — 39Vf2cm Transfer — 44Can Communication — 45Multiplex Communication — 20Power Distribution — 5Power Steering — 29Steering Column — 29Air Conditioning — 108Door Lock — 88Engine Hood / Door — 16Engine Immobiliser — 47Exterior — 55Horn — 5Interior — 18Interior Panel — 8Lighting — 93Meter / Gauge / Display — 31Mirror — 22Other System — 24Pre-collision — 40Seat — 52Seat Belt — 40Sliding Roof — 26Supplemental Restraint Systems — 139Theft Deterrent — 20Window / Glass — 53Wiper / Washer — 24
~1min read
DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C120B

IG Supply Voltage Low

Master cylinder pressure sensor power supply voltage decrease occurs or history of voltage decrease exists, and defective master cylinder pressure sensor output continues for 1 second or more.
  • Master cylinder pressure sensor output defective
  • Skid control ECU (Brake actuator assembly)
  • ABS NO. 2 fuse
WIRING DIAGRAM

Refer to DTC C1417 (See page CAUTION / NOTICE / HINT ).

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (See page ).
  • Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (+BS TERMINAL)

(a) Make sure that there is no looseness at the locking part and the connecting part of the connector.

(b) Disconnect the skid control ECU (brake actuator assembly) connector.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

S1-38 (+BS) - Body ground

Always

11 to 14 V

S1-38 (+BS) - S1-25 (GND1)

Always

11 to 14 V
Text in Illustration

*a

Front view of wire harness connector

(to Skid Control ECU [Brake Actuator Assembly])
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)
OK

  1. RECONFIRM DTC

(a) Reconnect the S1 skid control ECU (brake actuator assembly) connector.

(b) Clear the DTCs (See page ). (c) Check if the same DTC is recorded (See page ).

(c) Check if the same DTC is recorded (See page Result Result ).

Result

Result

Proceed to

DTC C120B is not output.

A

DTC C120B is output.

B
A

USE SIMULATION METHOD TO CHECK
B

REPLACE BRAKE ACTUATOR ASSEMBLY

Test yourself

A quick Toyota Tacoma quiz: every answer comes with an explanation and a link to the manual page.