DESCRIPTION
Power is supplied to the navigation receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.
WIRING DIAGRAM
NOTICE:
- The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.
Click here 
- Inspect the fuses for circuits related to this system before performing the following procedure.
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
PROCEDURE
CHECK METER / GAUGE SYSTEM
(a) Check if the rheostat function operates normally.
OK:
The rheostat function operates normally.
| NG |
 |
GO TO METER / GAUGE SYSTEM |
| OK |
 |
|
CHECK LIGHTING SYSTEM
(a) Check if the instrument panel illumination comes on normally.
OK:
The instrument panel illumination comes on normally.
| NG |
 |
GO TO LIGHTING SYSTEM |
| OK |
 |
|
CHECK ILLUMINATION
(a) Check if the illumination for the steering pad switch assembly or navigation receiver assembly comes on when the light control switch is turned to the head or tail position.
Result | Proceed to |
Illumination for steering pad switch assembly does not come on. |
A |
Illumination for navigation receiver assembly does not come on. |
B |
| B |
 |
GO TO STEP 7 |
| A |
 |
|
CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
(a) Disconnect the spiral cable sub-assembly connector.
Click here  |
 |
*a |
Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
|
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Switch Condition | Specified Condition |
J45-12 (IL+2) - Body ground |
Light control switch in the tail or head position |
11 to 14 V |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
| OK |
 |
|
INSPECT STEERING PAD SWITCH ASSEMBLY
(a) Remove the steering pad switch assembly.
Click here 
(b) Inspect the steering pad switch assembly.
Click here 
| NG |
 |
REPLACE STEERING PAD SWITCH ASSEMBLY |
| OK |
 |
|
INSPECT SPIRAL CABLE SUB-ASSEMBLY
(a) Remove the spiral cable sub-assembly.
Click here 
(b) Inspect the spiral cable sub-assembly.
Click here 
| OK |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
| NG |
 |
REPLACE SPIRAL CABLE SUB-ASSEMBLY |
CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
(a) Disconnect the navigation receiver assembly connector. |
 |
*a |
Front view of wire harness connector
(to Navigation Receiver Assembly) |
|
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Switch Condition | Specified Condition |
J133-10 (ILL+) - Body ground |
Light control switch in tail or head position |
11 to 14 V |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
(a) Disconnect the J134 navigation receiver assembly connector.
(b) Disconnect the J28 combination meter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
J134-5 (ILL-) - J28-22 (ILL-) |
Always |
Below 1 Ω |
| OK |
 |
REPLACE NAVIGATION RECEIVER ASSEMBLY |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|