Toyota Venza Quiz
Brake Control / Dynamic Control Systems

VSC OFF Indicator Light does not Come ON

In this manual: Brake Control / Dynamic Control Systems
Introduction — 15Maintenance — 8Audio / Video — 102Garage Door Opener — 8Navigation / Multi Info Display — 81Park Assist / Monitoring — 50Brake (front) — 7Brake (rear) — 7Brake Control / Dynamic Control Systems — 79Brake System (other) — 28Parking Brake — 22Axle And Differential — 44Drive Shaft / Propeller Shaft — 24Mf1a Transfer / 4wd / Awd — 46U660e Automatic Transmission / Transaxle — 1241ar-fe Cooling — 311ar-fe Emission Control — 101ar-fe Engine Control — 1331ar-fe Engine Mechanical — 441ar-fe Fuel — 311ar-fe Intake / Exhaust — 211ar-fe Lubrication — 111ar-fe Starting — 16Cruise Control — 241ar-fe Battery / Charging — 162gr-fe Battery / Charging — 17Networking — 67Power Distribution — 8Power Assist Systems — 34Steering Column — 37Steering Gear / Linkage — 29Alignment / Handling Diagnosis — 4Front Suspension — 39Rear Suspension — 35Tire / Wheel — 4Tire Pressure Monitoring — 35Door / Hatch — 83Exterior Panels / Trim — 56Horn — 4Lighting (ext) — 89Mirror (ext) — 36Sliding Roof / Convertible — 26Window / Glass — 87Wiper / Washer — 30Door Lock — 85Heating / Air Conditioning — 82Interior Panels / Trim — 20Lighting (int) — 37Meter / Gauge / Display — 41Mirror (int) — 9Power Outlets (int) — 10Seat — 84Seat Belt — 43Supplemental Restraint Systems — 131Theft Deterrent / Keyless Entry — 155
~2min read
DESCRIPTION

The skid control ECU is connected to the combination meter via CAN communication.

WIRING DIAGRAM

Refer to VSC OFF Indicator Light Remains ON (See page ).


PROCEDURE

  1. CHECK CAN COMMUNICATION SYSTEM

(a) Check if a CAN communication system DTC is output (See page ).


Result

Proceed to

DTC is not output

A

DTC is output

B

B

INSPECT CAN COMMUNICATION SYSTEM
A

  1. PERFORM ACTIVE TEST USING TECHSTREAM (VSC OFF INDICATOR LIGHT)

(a) Connect the Techstream to the DLC3.

(b) Start the engine.

(c) Select the Active Test on the Techstream (See page ).


ABS/VSC/TRAC

Tester Display

Test Part

Control Range

Diagnostic Note

VSC OFF Indicator Light

VSC OFF indicator light

Indicator light ON/OFF

Observe accessory meter

(d) Check that the VSC OFF indicator light on the accessory meter turns on or off in accordance with the Techstream operation.

OK:

The VSC OFF indicator light turns on or off in accordance with the Techstream operation.

HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page ).



OK

REPLACE BRAKE ACTUATOR ASSEMBLY
NG

  1. INSPECT COMBINATION METER ASSEMBLY

(a) Turn the ignition switch off.

(b) Turn the ignition switch to ON and check the VSC OFF indicator light will come on for approximately 3 seconds (initial check).

(c) Perform the Active Test of the combination meter (meter CPU) using the Techstream (See page ).


(d) Check the accessory meter.

Result

Proceed to

OK

A

NG (Initial check is normal, and the VSC OFF indicator light does not turn on or off in accordance with the Techstream operation)

B

NG (Initial check is abnormal)

C

HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page ).



A

REPLACE BRAKE ACTUATOR ASSEMBLY

B

REPLACE COMBINATION METER ASSEMBLY

C

REPLACE ACCESSORY METER ASSEMBLY

Test yourself

A quick Toyota Venza quiz: every answer comes with an explanation and a link to the manual page.